background image

XM1630S Software Reference Manual 

No. XM1630S-A00-104 

xmodus swiss GmbH 

13 / 32 

3.5  Web based administration 

 
 

The administration screen provides the possibility to change the user name and the 
password of your module. Furthermore you will be able to configure the FTP, 
TELNET and HTTP servers. 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
Important: 

 
Please pay attention that changes on this page are only accepted if the present 
password has been entered in the “Verify your present password” field. 
 
 

 

Enter a new password: 

This field allows entering a new password. It is validated 

by the “Confirm your new password” field. These fields must be identical. 

 

Menu Login:

 Select this radio button if a login is required to enter the terminal 

menu from a Telnet connection. 

 

FTP Server:

 This radio button defines if the FTP server of the module is 

accessible from the remote side. The FTP server enables modification of the web 
pages. Disable it to protect against unwanted modifications. 

 

Telnet Server:

 This radio button enables the Telnet server of the module. Disable 

it to block login via Telnet from remote site. The field “Telnet port” selects the port 
number of the server (default 23 – standard Telnet port number). 

 

HTTP Server Login:

 This radio button enables authentication so that the web 

server requests login on contact.  

 

Trusted IP address:

 If “Trusted IP address” field is set non-zero, only the 

specified IP address (trusted address) is allowed to login on to the module to 
perform configuration and monitoring. All other source addresses will be rejected. 

 
 
 

Summary of Contents for XM1630S

































Reviews: