background image

XOS  

|

  801377-02  

|

  Rev D  

|

  English

 

 

 

 

 

Page 

3

 of 

22 

 

 

Electrical Exposure

: If any main system 

components are opened or dissembled, 

electrical components will be exposed that can 

produce a dangerous electrical shock. The X-

Ray components operate at high electrical 

voltages of up to 50 kilovolts, which can be 

lethal. It is the customer’s responsibility to 

ensure the electronics are properly grounded 

to earth. Service of the analyzer must be 

performed by authorized service personnel 

who are trained to work with high-voltage 

equipment. 

 

Thermal Exposure

: The components inside 

the equipment can reach high temperatures 

that can be potentially hazardous to the user. 

 

WARNING

 

This product can expose you to chemicals 

including lead/lead compounds which are 

known to the State of California to cause 

cancer or birth defects or other reproductive 

harm.  For more information, go to: 

            

www.p65warnings.ca.gov

 

 

Radiation Safety Statement 

This Product conforms to all applicable Standards under U.S. 

21 C.F.R. Chapter I, Subchapter J and IEC EN 61010-1. 

Each product is delivered with a radiation survey report that 

summarizes the radiation emission testing performed at the 

XOS factory before shipment.  The Product should be 

surveyed periodically by appropriate radiation safety personnel 

or qualified outside contractors.  

 

Radiation Safety Compliance 

This Product is sold with the understanding that the user 

assumes sole responsibility for radiation safety, as well as any 

state, provincial, or local regulatory compliance.  Such 

regulations may require but are not limited to: machine 

registration, personnel qualification, periodic survey 

requirements, maintaining a safety program, and/or 

maintaining a dosimetry program.  Users must consult the 

applicable regulating bodies for further information on user 

responsibilities.  Consult the full User Manual shipped with the 

Product for detailed Product description and additional safety 

and radiation information

.  

 

Summary of Contents for Petra 4294


























Reviews: