12
FACTORY PROGRAMS
GENERAL
uses low and high frequencies and gives an excellent assessment of targets in the soil. It suits
both beginners and experienced users.
It offers an excellent target/false signal ratio in the ground,
as it rejects the moisture in the soils, which can
cause halos and false sounds when passing over holes, for example. You will therefore have more confi-
dence on deep targets. This damp / wet soil subtraction thus attenuates the very low electric conductors
like coke (coal, and conductive stone) and to a lesser extent certain very thin targets like aluminum foil.
•
Very effective, test it in the soil, not in the air.
•
Set the Reactivity to 1 - 1.5 for more efficiency in cleaner soil or to 2.5 - 3 for polluted/mineralized soil.
•
You can lower Frequency Max to 14KHz to be less sensitive to low conductive targets, such as small
aluminium foil and more sensitive to high conductive targets such as large silver coins.
has the advantage of offering a wide range of programs suitable for all ground and search condi-
tions. Unlike some multi-frequency detectors that offer fixed multiple frequencies,
uses different
high and low frequency combinations depending on the programs. For example, some use low to medi-
um frequencies e.g. 4 to 14 kHz and other programs include higher frequencies up to 24 kHz or 40 kHz.
Program-specific signal processing is applied to these frequency combinations and to the ground in the
best possible way. These frequencies can then be subtracted to remove electrically-conductive soils or
added together to help locate a wider range of targets. The processing platform information used for each
program is displayed in the title bar. Read the data for each program carefully to get the most out of your
!
(See also the comparison table at the end of the manual to better understand the different parameters
each program has to offer).
SENSITIVE
uses low and high frequencies up to about 40 kHz. Highly efficient on all targets, it will be
very
effective in mineralized and polluted ground when searching for the smallest targets.
•
Thanks to the high precision that the DEUS II carries, coke and humidity can be classified with high-
er accuracy than with a mono-frequency metal detector. A very narrow notch zone is thus activated
within frequencies 23 to 24 (see Notch > Expert).
•
Reduce the Reactivity to 2 for more efficiency in cleaner ground or increase it to 3 for polluted or
mineralized ground.
SENSITIVE FULL TONES
is based on the same platform as Prg. 2 - SENSITIVE, but it is configured using
Full Tone audio mode, with Reactivity at 3 instead of 2.5. It offers a very rich and informative sound identifi-
cation that requires a little more experience, as each target index generates a different tone in proportion
to conductivity (see Discri > Full Tones). Very efficient in highly-polluted ferrous and mineralized ground.
FAST
is based on the same platform as Prg. 2 - SENSITIVE, but the audio is set to Pitch mode with Re-
activity at 3 instead of 2.5 and uses the square audio feature. These three settings combined allow the
machine to work fast in ferrous-polluted and mineralized ground.
PARK
is adjusted for searching recreational area’s such as, parks, dry sand beach, etc., sites that are
normally polluted.
•
A notch is active from 23 to 35 to reject aluminum foil. Increase it if necessary.
•
B.Caps is set to 2 to reject most rusty ferrous caps.
DEEP HIGH CONDUCTOR
adds together very low and medium frequencies up to 14 kHz.
Designed to better locate good conductivity targets, it is ideal for clusters of coins whilst maintaining ex-
cellent sensitivity to isolated coins using its 14 kHz frequency.
•
Ground Stability could be set to 1 and soils above your setting will therefore sound to provide you with
the best performance for specific deep searches (see Ground). Adjust the Ground by Grabbing but If
you are experiencing too many false signals, re-adjust GND Stability at 2 to reject all the soils, ferrites
and shocks.
Prg. 2 - SENSITIVE
FMF • Max. freq. 40khz • Frequency addition
Prg. 3 - SENSI FT
FMF • Max. freq. 40khz • Frequency addition
Prg. 4 - FAST
FMF • Max. freq. 40khz • Frequency addition
Prg. 5 - PARK
FMF • Max. freq. 24khz • Frequency addition
Prg. 6 - DEEP HC
FMF • Max. freq. 14khz • Frequency addition
Prg. 1 - GENERAL
FMF • Max. freq. 40khz • Conductive soil subtraction
