background image

1

1. Safety Summary

 

 

The following safety precautions apply to both operating and 
maintenance personnel and must be observed during all 
phases of operation, service, and repair of this instrument. 
Before applying power, follow the installation instructions and 
become familiar with the operating instructions for this 
instrument.  
 
Failure to comply with these precautions or with specific 
warnings elsewhere in this manual violates safety standards 
of design, manufacture, and intended use of the instrument.   
XP Power assumes no liability for a customer’s failure to 
comply with these requirements.

 

 
GROUND THE INSTRUMENT  
 

To minimize shock hazard, the instrument chassis and cabinet must be connected to an electrical ground.  This instrument is 
grounded through the ground conductor of a three-conductor AC power cable.  The power cable must be plugged into an 
approved three-conductor electrical outlet.  Do not alter the ground connection.  Without the protective ground connection, all 
accessible conductive parts (including control controls) can render an electric shock.  The power jack and mating plug of the 
provided power cable meet IEC safety standards. 

 

 
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE  
 

Do not operate the instrument in the presence of flammable gases or fumes.  Operation of any electrical instrument in such an 
environment constitutes a definite safety hazard. 

 

 
KEEP AWAY FROM LIVE CIRCUITS  
 

Instrument covers must not be removed by operating personnel.  Component replacement must only be made by qualified 
maintenance personnel.  Removal of the cover will void the warranty.  Under certain conditions, even with the power cable 
removed, dangerous voltages may exist.  To avoid injuries, always disconnect power and discharge circuits before touching 
them. 

 

 
DO NOT SERVICE OR ADJUST ALONE  
 

Do not attempt any internal service.  This unit contains no user serviceable components.  Removal of the cover will void the 
warranty.

 

 
DO NOT SUBSTITUTE PARTS OR MODIFY THE INSTRUMENT  

 
Do not install substitute parts or perform any unauthorized modifications to this instrument.  Return the instrument to XP Power 
for service and repair to ensure that safety features are maintained. 

 

USER MANUAL 

­

 PLS1500 SERIES

Summary of Contents for PLS1500 Series











































Reviews: