background image

 

https://www.XPOtool.com 

 

Item 63027

 

Page 12

 

The Tool Experts

 

 

  

 

01 2022

-1

 

 

Disposal regulations

 

 
 

EU  guidelines  regarding  the  disposal  of  scrap  electric  appliances  (WEEE,  2012/19/EU)  were  imple-
mented in the law related to electrical and electronic equipment and appliances.

 

 

All  WilTec  electric  devices  that  fall  under  the  WEEE  regulations  are  labelled  with  the  crossed-out 
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the 
domestic waste.

 

 

The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE-
registration number DE45283704.

 

 

Disposal  of  used  electrical  and  electronic  appliances 
(intended for use in the countries of the European Un-
ion and other European countries with a separate col-
lection system for these appliances).

 

The logo on the article or on its packaging points out 
that this article must not be treated as normal house-
hold waste but must be disposed to a recycling collec-
tion point for electronic and electrical waste equipment. 
By contributing to the correct disposal of this article you 
protect the environment and the  health  of your  fellow 
men. Environment and health are threatened by inap-
propriate disposal.

 

 

Material recycling helps reduce the consumption of raw materials.

 

 

Additional information on recycling this article can be provided by your local community, municipal waste 
disposal facilities, or the store where you purchased the article.

 

 
 
 
 

Address:

 

WilTec Wildanger Technik GmbH

 

Königsbenden 12 / 28

 

D-52249 Eschweiler

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Important notice:

 

 

The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction 
manual require the written permission of WilTec Wildanger Technik GmbH.

 

Summary of Contents for 63027













Reviews: