background image

31

              IMPORTANT NOTES – ELECTRICAL

•  Insulate any exposed electrical wiring (using heat shrink tubing or electrical tape) to prevent dangerous short circuits. 

Take maximum care in wiring, connecting and insulating cables. Make sure cables are always connected securely. Check 
connectors for if they become loose. And if so, reconnect them securely. Never use R/C models with damaged wires. A 
damaged wire is extremely dangerous, and can cause short-circuits resulting in fi re. Please have wires repaired at your 
local hobby shop.

•  Low battery power will result in loss of control. Loss of control can occur due to a weak battery in either the transmitter 

or the receiver. Weak running battery may also result in an out of control car if your car‘s receiver power is supplied by 
the running battery. Stop operation immediately if the car starts to slow down.

•  When not using RC model, always disconnect and remove battery. 
•  Do not disassemble battery or cut battery cables. If the running battery short-circuits, approximately 300W of electricity 

can be discharged, leading to fi re or burns. Never disassemble battery or cut battery cables.

•  Use a recommended charger for the receiver and transmitter batteries and follow the instructions correctly. Over-

charging, incorrect charging, or using inferior chargers can cause the batteries to become dangerously hot. Recharge 
battery when necessary. Continual recharging may damage battery and, in the worst case, could build up heat leading 
to fi re. If battery becomes extremely hot during recharging, please ask your local hobby shop for check and/or repair 
and/or replacement.

•  Regularly check the charger for potential hazards such as damage to the cable, plug, casing or other defects. Ensure 

that any damage is rectifi ed before using the charger again. Modifying the charger may cause short-circuit or 
overcharging leading to a serious accident. Therefore do not modify the charger.

•  Always unplug charger when recharging is fi nished.
•  Do not recharge battery while battery is still warm. After use, battery retains heat. Wait until it cools down before 

charging. 

•  Do not allow any metal part to short circuit the receiver batteries or other electrical/electronic device on the model.
•  Immediately stop running if your RC model gets wet as may cause short circuit. 
•  Please dispose of batteries responsibly. Never put batteries into fi re. 

WARRANTY

XRAY guarantees this model kit to be free from defects in both material and workmanship within 30 days of 
purchase. The total monetary value under warranty will in no case exceed the cost of the original kit purchased. This 
warranty does not cover any components damaged by use or modifi cation or as a result of wear. Part or parts missing 
from this kit must be reported within 30 days of purchase. No part or parts will be sent under warranty without proof 
of purchase. Should you fi nd a defective or missing part, contact the local distributor. Service and customer support 
will be provided through local hobby store where you have purchased the kit, therefore make sure to purchase any 
XRAY products at your local hobby store. This model racing car is considered to be a high-performance racing vehicle. 
As such this vehicle will be used in an extreme range of conditions and situations, all which may cause premature 
wear or failure of any component. XRAY has no control over usage of vehicles once they leave the dealer, therefore 
XRAY can only offer warranty against all manufacturer‘s defects in materials, workmanship, and assembly at point 
of sale and before use. No warranties are expressed or implied that cover damage caused by what is considered 
normal use, or cover or imply how long any model cars‘ components or electronic components will last before 
requiring replacement.

Due to the high performance level of this model car you will need to periodically maintain and replace consumable 
components. Any and all warranty coverage will not cover replacement of any part or component damaged by 
neglect, abuse, or improper or unreasonable use. This includes but is not limited to damage from crashing, chemical 
and/or water damage, excessive moisture, improper or no maintenance, or user modifi cations which compromise the 
integrity of components. Warranty will not cover components that are considered consumable on RC vehicles. XRAY 
does not pay nor refund shipping on any component sent to XRAY or its distributors for warranty. XRAY reserves the 
right to make the fi nal determination of the warranty status of any component or part.

QUALITY CERTIFICATE

XRAY MODEL RACING CARS uses only the highest quality materials,  the best compounds for molded parts and the most sophisticated 
manufacturing processes of TQM (Total Quality Management). We guarantee that all parts of a newly-purchased kit are manufactured 
with the highest regard to quality. However, due to the many factors inherent in model racecar competition, we cannot guarantee 
any parts once you start racing the car. Products which have been worn out, abused, neglected or improperly operated will not be 
covered under warranty. 

We wish you enjoyment of this high-quality and high-performance RC car and wish you best success on the track!

LIMITATIONS OF LIABILITY

XRAY makes no other warranties expressed or implied. XRAY shall not be liable for any loss, injury or damages, whether 
direct, indirect, special, incidental, or consequential, arising from the use, misuse, or abuse of this product and/or any 
product or accessory required to operate this product. In no case shall XRAY‘s liability excess the monetary value of this 
product.

Take adequate safety precautions prior to operating this model. You are responsible for this model’s 
assembly and safe operation.

Disregard of the any of the above cautions may lead to accidents, personal injury, or property damage. XRAY 
MODEL RACING CARS assumes no responsibility for any injury, damage, or misuse of this product during 
assembly or operation, nor any addictions that may arise from the use of this product. All rights reserved.

Summary of Contents for M18 PRO

































Reviews: