XTA DeltaDirect for iPad Quick Start Manual Download | Manualshive

Page: 13 / 14

background image

DeltaDirect Quick Start Guide Page 13

You can still access individual device channels when using grouping, but channels in absolute groups
will not allow EQ to be edited — they will show the EQ and detail which group they are part of so it’s
quick to switch to that group and make changes as required.

«
...
11
12
13
14
»

Summary of Contents for DeltaDirect for iPad















Reviews:

No comments

Related manuals for DeltaDirect for iPad

Brand: Parasound Pages: 16

Brand: Cambridge Audio Pages: 16

Brand: Offel Pages: 2

Brand: Harman Pages: 2

Brand: Harley Benton Pages: 12

Brand: rabbitone Pages: 2

Brand: Velleman Pages: 29

Brand: D.W. Fearn Pages: 21

ProX 840.4 COMP

Brand: µ-Dimension Pages: 12

VIV Six Five Series

Brand: Memphis Pages: 16

Brand: Akai Pages: 22

IronHorse DH40H

Brand: Traynor Pages: 18

Brand: DAPAudio Pages: 12

Brand: Audio international Pages: 12

Acoustic Performer Pro

Brand: Fishman Pages: 24

Brand: McIntosh Pages: 20

Brand: DSM Pages: 8

Brand: Parallel Audio Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands