background image

                                                                                                                                         

Xterra  FS420e  Elliptical

2

Thank you for your purchase of this quality elliptical trainer from Xterra. Your new
elliptical has been manufactured by one of the leading fitness manufacturers in the world
and is backed by one of the most comprehensive warranties available. Xterra will do all
we can to make your ownership experience as pleasant as possible for many years to
come.

If you have questions, or if parts are missing or damaged, or you require customer
service, call (870) 935-1107. Please have your Model number and serial number handy
when you call.

Please take a moment at this time to record below the name of the store, their telephone
number, and the date of purchase for easy contact in the future. We appreciate your
confidence in Xterra and we will always remember that you are the reason that we are in
business. Please complete and mail your registration card today and enjoy your new
elliptical.

Yours in Health,
The folks at Xterra Fitness

Name  of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase  Date_______________________________________

RECORD YOUR SERIAL NUMBER

Please record the Serial Number of this fitness product in the space provided below.

Serial Number

_______________________________________

REGISTER YOUR PURCHASE

The self-addressed product registration card must be completed in full and returned to Xterra
fitness, or visit:

www.xterrafitness.com

 to register online.

FS420e_Ver.A

Product Registration

CONGRATULATIONS ON YOUR

NEW ELLIPTICAL AND WELCOME

TO THE XTERRA FAMILY!

Summary of Contents for FS420e























Reviews: