7
#102
. 5/16” × 2-1/4”
Hex Head Bolt (4 pcs)
#103
. 3/8” × 3/4”
Hex Head Bolt (2 pcs)
#104
. 3/8” × 1-1/2”
Hex Head Bolt (2 pcs)
#105
. 3/8” × 2-1/4”
Hex Head Bolt (1 pc)
#116
. M5 × 10mm
Phillips Head Screw
(4 pcs)
#130
. 3/8” × 7T
Nyloc Nut (2 pcs)
#137
. 3/8” × 19 × 1.5T
Flat Washer (2 pcs)
#142
. 5/16” × 20 × 1.5T
Flat Washer (4 pcs)
#151
. 5/16” × 1.5T
Split Washer (4 pcs)
#152
. 3/8” × 2T
Split Washer (1 pc)
#153
. 3/8” × 23 × 2T
Curved Washer (2 pcs)
#154
. 5/16”
Star Washer (4 pcs)
1
Assembly Tools
Assembly Instructions
Rear Rail, Console Mast & Console
1. Slide the Incline Rail Assembly (
2
) into the U channel of the Main Frame (
1
).
Be very careful not to damage the wires that exit each part.
2. Connect the Incline Rail Assembly (
2
) horizontally to the U channel of the
Main Frame (
1
) with two Hex Head Bolts (
104
), two Flat Washers (
137
) and
two Nyloc Nuts (
130
). Secure it vertically with four Hex Head Bolts (
102
),
four Split Washers (
151
), four Flat Washers (
142
) and four Star Washers
(
154
). Tighten using the Wrenches provided (
155
&
158
).
3. Connect the Incline Motor wires (
49
&
50
) to the wiring harness that exits the
Incline Rail Assembly (
2
), by matching the colors red, white and black. Push
the excess cable inside the U channel. Guide the twist tie that is attached to
the Computer Cable (
44
) through
Mast Cover (72) and
the bottom of the
Console Mast (
12
) until it exits the top of the steel tube. Secure the Console
Mast (
12
) by loosely threading two Hex Head Bolts (
103
) from the front and
two Curved Washers (
153
) first. Then secure the mast from the side by
loosely threading a Hex Head Bolt (
105
) and a Split Washer (
152
).
Note
:
There is one bolt already installed in the receiving bracket that will engage
with the slot at the bottom of the Console Mast. Tighten the two bolts from
the left side last.
4. Tighten the two front bolts first, then the side bolts with the Wrench (
155
).
5. Untie the twist tie from around the Computer Cable (
44
). Plug the Computer
cable (
44
- wide white end) & the two Hand Pulse Cables (
47
) into the
bottom of the Console (
43
). Insert the Resistance Cable (
165
) into the white
port labeled “Load” and the Incline Cable (
166
) into the Incline port on the
back of the Console. Secure the Console (
43
) onto the mounting plate with
four Phillips Head Screws (
116
). Tighten them with the Phillips Head Screw
Driver (
157
).
6. Install the water bottle holder onto the handlebar in any position you like.
Hardware Step 1
#157
. Phillips
Head Screwdriver
#155
. 13/14mm Wrench
#158
. 12/14mm Wrench
Summary of Contents for FS5.8e
Page 1: ......
Page 8: ...8 1Rear Rail Console Mast Console ...
Page 26: ...26 EXPLODED VIEW DIAGRAM ...
