Xtracycle EdgeRunner Classic Assembly Manual Download

Page: 6 / 17

Install the Fork

tep 4

Find the headset and spacers in the included small

parts box, and the S/M/L sized stem (paired with

seatpost) in the separately-shipped accessory box.

The headset includes a thin rubber seal that sits on the

lip of the crown race. Install this first, then the lower

bearing (the lower bearing is larger than the upper).

Grease liberally.

Slide the steerer tube up through the headtube,

taking care to make sure the hoses and housing are

routed correctly.

Pro tip:

Zip-tie or toe-strap the fork to the

down-tube to assist during stem/headset assem-

bly.

Note:

The cable housing and hoses are routed

past the head tube on the same side as they

come up the down tube - don’t cross them under

the downtube!

Summary of Contents for EdgeRunner Classic


















Search results

Summary of Contents for EdgeRunner Classic

Reviews:

Related manuals for EdgeRunner Classic

Brands by name

Popular brands

Xtracycle EdgeRunner Classic, Assembly Manual

Search results

Summary of Contents for EdgeRunner Classic

Reviews:

Related manuals for EdgeRunner Classic

Brands by name

Popular brands