Xtracycle RFA Assembly Manual Download | Manualshive

Page: 4 / 15

background image

4

08

With a friend, lift the bike out of the box and set it on your
work surface.

10 - Charge the battery

Remove the battery keys secured to the handlebars.

09

Remove the zip-ties holding the front wheel to the frame and
set it aside.

11

Unlock your battery and remove it by rotating it away from
the bike.

«
...
2
3
4
5
6
...
»

Summary of Contents for RFA
















Reviews:

No comments

Related manuals for RFA

Brand: Yakima Pages: 18

Brand: Larry vs Harry Pages: 7

Brand: Specialized Pages: 35

Brand: Rose electronics Pages: 2

Brand: Rose electronics Pages: 99

Brand: Tower Hobbies Pages: 11

Brand: QPlay Pages: 6

Brand: Nireeka Pages: 29

Brand: KINGSONG Pages: 9

Brand: Ergon Pages: 104

Brand: Wisper Pages: 30

Brand: Kinderkraft Pages: 44

Brand: OKBABY Pages: 59

PORTOTRIKE PT, PORTOTRIKE PT2F, PORTOTRIKE PTCB, PORTOTRIKE PT2CB, PORTOTRIKE PT3CB

Brand: Worksman Pages: 6

RACE ATTACK SL-160 CARBON

Brand: Rose electronics Pages: 2

Single Seat Bicycle Trailer

Brand: InStep Pages: 17

Brand: Whyte Pages: 10

Brand: Whyte Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands