Xtracycle RFA Assembly Manual Download | Manualshive

Page: 7 / 15

background image

7

20

Using the ball or short end of the Allen wrench, tighten the
two rear bolts.

21

Using the shorter end of the Allen wrench, tightly secure all
bolts in place.

22 - Install the front wheel

Carefully lift the front of the bike and deploy the kickstand.

23

Remove the packaging around the fork and fender. Remove
the thru-axel with a 6 mm Allen wrench.

«
...
5
6
7
8
9
...
»

Summary of Contents for RFA
















Reviews:

No comments

Related manuals for RFA

Brand: Hamax Pages: 74

Alloy Road Disc

Brand: Cannondale Pages: 16

Brand: Cygolite Pages: 2

Brand: Chipolino Pages: 8

Brand: Puky Pages: 36

Brand: Dillenger Pages: 23

Brand: Dillenger Pages: 26

Brand: Dillenger Pages: 26

Brand: ProActiv Pages: 52

Brand: King-Meter Pages: 17

Brand: Power-Ped Pages: 16

Brand: Prevelo Pages: 32

Brand: SKS Germany Pages: 52

Brand: eelo Pages: 12

RACE ATTACK SP-63 XL

Brand: Rose electronics Pages: 2

Brand: FALK Pages: 79

Brand: VDO Cyclecomputing Pages: 51

Brand: BikeBoard Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands