Xtracycle STOKER Assembly Manual Download | Manualshive

Page: 14 / 15

background image

14

47 - Complete assembly

Tie down the two hook and loop straps on the bottom of the
FreeLoader Too bags to the bike frame.

48

The Stoker assembly is complete and you are ready to ride!

Looking to install additional accessories

on your Stoker?

Please refer to the following page on the Xtracycle
wesbite for links to additional installation manuals:

https://www.xtracycle.com/product-manuals

«
...
12
13
14
15
»

Summary of Contents for STOKER
















Reviews:

No comments

Related manuals for STOKER

Brand: Ultra motor Pages: 34

Brand: Mad4One Pages: 5

Brand: Youin Pages: 52

Brand: HP Velotechnik Pages: 6

Brand: MoMi Pages: 12

Brand: Skiddoü Pages: 36

Brand: EG Pages: 10

Brand: Qualisports Pages: 5

Mid drive Series

Brand: VelectriX Pages: 27

BEP-NRH005 Series

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 35

Brand: Achiever Pages: 44

PEDELEC IMPULSE 2.0 ERGO

Brand: Derby cycle Pages: 34

Brand: FiSHAW Pages: 65

Brand: E-Bike Pages: 45

Brand: Liberty Electric Bikes Pages: 19

Mini Trax MTX-PREMA

Brand: Hauck Pages: 2

Brand: Lupine Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands