background image

Xtreme Power Conversion Corporation

TX90 User’s Manual

Page 23

Uninterruptible Power Supply

Xtreme Power Conversion Limited Warranty

Xtreme Power Conversion (XPC) Corporation warrants Xtreme Power Conversion equipment, when properly ap-

plied and operated within specified conditions, against faulty materials or workmanship for a period of 

three years 

for TX90-Series products

 from the date of purchase.  XPC Corporation warrants 

internal batteries for a period of 

three years 

from the date of purchase. For equipment sites within the United States and Canada, this warranty 

covers repair or replacement, at the sole discretion of XPC Corporation. The customer is responsible for the costs 

of shipping the defective product to XPC Corporation. XPC Corporation will pay for ground shipment of the re-

paired or replacement product. This warranty applies only to the original purchaser.

If equipment provided by XPC Corporation is found to be 

Dead-on-Arrival (DOA)

, XPC Corporation will be respon-

sible for the costs of shipping product to and returning equipment from the customer in a timely manner as agreed 

to with the customer, once the customer has requested and received a 

Return Material Authorization (RMA)

 

number. DOA equipment is defined as equipment that does not properly function according to user documenta-

tion when initially received and connected in conjunction with proper procedures as shown in the user documen-

tation or via support provided by XPC Corporation personnel or authorized agents.

This warranty shall be void if (a) the equipment is repaired or modified by anyone other than XPC Corporation or 

a XPC Corporation approved third party; (b) the equipment is damaged by the customer, is improperly used or 

stored, is subjected to an adverse operating environment, or is operated outside the limits of its electrical specifi-

cations; or (c) the equipment has been used or stored in a manner contrary to the equipment’s operating manual, 

intended use or other written instructions. Any technical advice furnished by XPC Corporation or a XPC Corpora-

tion authorized representative before or after delivery with regard to the use or application of Xtreme Power Con-

version equipment is furnished on the basis that it represents XPC Corporations best judgment under the situation 

and circumstances, but it is used at the recipient’s sole risk.

EXCEPT AS STATED ABOVE, XPC Corporation DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

EXCEPT AS STATED ABOVE, IN NO EVENT WILL XPC Corporation BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCI-

DENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF Xtreme Power Conversion EQUIPMENT, 

including but not limited to, any costs, lost profits or revenue, loss of equipment, loss of use of equipment, loss 

of software, loss of data, cost of substitutes, or claims by third parties. Purchaser’s sole and exclusive remedy for 

breach of any warranty, expressed or implied, concerning Xtreme Power Conversion equipment, and the only 

obligation of XPC Corporation under this warranty, shall be the repair or replacement of defective equipment, 

components, or parts; or, at XPC Corporations sole discretion, refund of the purchase price or substitution of an 

equivalent replacement product. 

Summary of Contents for TX90-1000



























Reviews: