Xtreme Power 75159 Owner'S Manual And Safety Instructions Download | Manualshive

Page: 11 / 12

background image

MAINTENANCE AND TROUBLESHOOTING

9

Confirm the screws in the baseboard are installed tightly. If any are found, re-tighten them before use.

Confirm the power cords are in good condition. If any parts are worn, cracked or in bad condition,

replace them prior to starting the pump.
The pump should be stopped immediately if the temperature is too high. Inspect and if need be, have

a technician repair it.
If loud noises are coming from the pump, turn the power off immediately and have a service technician

service and repair it.

TROUBLESHOOTING

«
...
9
10
11
12
»

Summary of Contents for 75159













Reviews:

No comments

Related manuals for 75159

Brand: Tanco Pages: 72

Brand: HABYS Pages: 16

Brand: Acterna Pages: 72

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: GE Pages: 154

Arize Element Top Light

Brand: GE Pages: 2

Brand: Datex-Ohmeda Pages: 104

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 166

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 340

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: Panasonic Pages: 180

Brand: Dairyland Pages: 21

Brand: Eazyzap Pages: 32

Brand: Obdstar Pages: 42

Brand: Parkside Pages: 58

Brand: Yamaha Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands