Xtreme NXTI 3P-1P User Manual Download

Page: 2 / 33

Xtreme Power Conversion Corporation

NXTi 3P-1P User’s Manual

Page 2

Uninterruptible Power Supply

Table of Contents

Safety and EMC Instructions.........................................................................3

Transportation and Storage.............................................................................................................3

Preparation......................................................................................................................................3

Installation.......................................................................................................................................3

Standards.........................................................................................................................................4

Installation and Operation............................................................................4

Unpacking and Inspection...............................................................................................................4

Rear Panel View...............................................................................................................................5

Single UPS Installation.....................................................................................................................6

UPS Installation for Parallel System.................................................................................................7

Software Installation........................................................................................................................8

Operations...................................................................................................9

Button Operation.............................................................................................................................9

LED Indicators and LCD Panel..........................................................................................................9

Audible Alarm................................................................................................................................11

Single UPS Operation.....................................................................................................................12

Parallel Operation..........................................................................................................................15

Abbreviation Meaning in LCD Display............................................................................................16

LCD Setting....................................................................................................................................18

Operating Mode/Status Description.............................................................................................24

Fault Code.....................................................................................................................................29

Warning Indicator..........................................................................................................................29

Warning Code...............................................................................................................................

Troubleshooting.........................................................................................30
Storage and Maintenance...........................................................................32

Storage...........................................................................................................................................32

Maintenance.................................................................................................................................32

Specifications.............................................................................................33

Summary of Contents for NXTI 3P-1P

































Search results

Summary of Contents for NXTI 3P-1P

Reviews:

Related manuals for NXTI 3P-1P

Brands by name

Popular brands

Xtreme NXTI 3P-1P, User Manual

Search results

Summary of Contents for NXTI 3P-1P

Reviews:

Related manuals for NXTI 3P-1P

Brands by name

Popular brands