Xtreme R91-20KVA User And Installation Manual Download | Manualshive

Page: 2 / 36

background image

Xtreme Power Conversion Corporation

R91 User’s Manual

Page 2

Uninterruptible Power Supply

Table of Contents

Introduction.................................................................................................6
Product Description.....................................................................................6

Main Features.................................................................................................................................6

System Configuration...................................................................................7

Unpacking the UPS..........................................................................................................................7

Installation Notes............................................................................................................................8

External Protective Devices.............................................................................................................8

Power Cables...................................................................................................................................9

Power Cables Connection................................................................................................................9

Battery Connection........................................................................................................................11

UPS Multi-Module Installation......................................................................................................13

Operation...................................................................................................16

Operation Modes..........................................................................................................................16

Turn On / Off the UPS....................................................................................................................17

Communication Port Definitions (RS232, RS485)..........................................................................23

LCD Display....................................................................................................................................24

Options..........................................................................................................................................32

Troubleshooting.........................................................................................33
Specifications.............................................................................................34
Shipping List.............................................................................................. 34
Obtaining Service.......................................................................................35
Xtreme Power Conversion Limited Warranty..............................................36

«
1
2
3
4
...
»

Summary of Contents for R91-20KVA





































Reviews:

No comments

Related manuals for R91-20KVA

SLC-700-TWIN RT2 (B0)

Brand: Salicru Pages: 48

SmartOnline SU16KRTHW

Brand: Tripp Lite Pages: 6

Brand: CABAC Pages: 20

Brand: Eaton Pages: 2

Brand: Eaton Pages: 13

Brand: TyconSolar Pages: 8

Brand: Eaton Pages: 44

SPECLINE AVR 700

Brand: Ever Pages: 2

S70 Line?Interactive

Brand: Xtreme Power Conversion Pages: 18

Brand: Tech Novitas Pages: 39

Brand: X-TREME Pages: 40

Imperial Series IMD-1000AP

Brand: Farnell Pages: 18

Brand: Xmart Pages: 4

Brand: Xtreme Power Conversion Pages: 9

Brand: CyberPower Pages: 10

Brand: Eaton Pages: 82

LIEBERT PSI5 MINI-TOWER PSI5-1500MT120

Brand: Vertiv Pages: 58

Liebert NXL 1100

Brand: Vertiv Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands