www.XMFG.com
Operation Manual
36
Operator Cab
A. HIGH HYDRAULIC OIL TEMP
The hydraulic oil temperature indicator illuminates when the
oil temperature is above 1800 F. If the hydraulic oil temperature
indicator illuminates, stop and idle the engine to allow time
for cooling. If the hydraulic oil temperature indicator does
not go out after five (5) minutes, stop the telehandler, follow
proper shut down procedures, tag the telehandler with “Do
Not Operate” tags, and have a qualified mechanic service or
repair the telehandler BEFORE placing it into service again.
B. WATER IN FUEL
The Water in Fuel Indicator will be displayed when there is
water present in the Diesel fuel.
C. LOW BRAKE PRESSURE INDICATOR AND WARNING
The Low Brake Pressure indicator illuminates if the hydraulic
oil pressure gets too low. If the Low Brake Pressure indicator
is illuminated, do not release the parking brake or engage
transmission until the indicator is out. If the indicator does
not go out, stop the telehandler, follow proper shut down
procedures, tag telehandler with “Do Not Operate” tags, and
have a qualified mechanic service or repair the telehandler
BEFORE placing it into service again.
D. LOW OIL PRESSURE WARNING
The Oil Pressure Warning is displayed when the engine oil
pressure is DANGEROUSLY low, 0-10 psi. If the Oil Pressure
Warning comes on during normal operation, stop the
telehandler, follow proper shut down procedures, tag
telehandler with “Do Not Operate” tags, and have a qualified
mechanic service or repair the telehandler BEFORE placing it
into service again.
E. WAIT TO START
The Wait to Start Indicator is displayed when the key switch is
moved to the RUN position. Wait until the indicator goes out
before starting the engine.
F. SERVICE REMINDER
The Service Reminder Indicator flashes for 30 seconds at key
ON to indicate that Service is required.
G. REAR AXLE LOCKED INDICATOR
Indicates that the rear axle is locked at or above 40 degrees
boom angle.
H. TACHOMETER
The Tachometer indicates engine RPM using an analog display
and below it a digital display.
I. CLOCK
J. OIL PRESSURE INDICATOR
The Oil Pressure Indicator monitors the engine oil pressure.
At normal operating pressure it stays green (above 20
psi). Between 12-20 psi it turns yellow and below 10 psi it
becomes red. If the indicator turns red (shows oil pressure
below 10psi) and the Oil Pressure Warning (red) is displayed,
stop the telehandler, follow proper shut down procedures, tag
telehandler with “Do Not Operate” tags, and have a qualified
mechanic service or repair the telehandler BEFORE placing it
into service again.
K. REAR AXLE CENTERED INDICATOR
Illuminates when the rear wheels are centered.
L. DIRECTION OF TRAVEL INDICATOR
Displays the direction of travel selected: Forward or reverse.
M. FUEL GAUGE
The fuel gauge indicates the percentage of fuel left in the
tank. The total capacity of the fuel tank is 48 gallons (181
L). Above 20% of fuel left in the tank, the indicator is green,
turning yellow between 10 and 20%. It turns red when the fuel
level is very low, 10% and under.
N. TRANSMISSION GEAR INDICATOR
Displays the transmission gear selected. The available
positions are: 1, 2, 3, and Automatic. Automatic is displayed as
A1, A2, or A3, with the numbers representing the current gear
the transmission is in.
O. ENGINE COOLANT TEMP INDICATOR
The Engine Coolant Temp Indicator monitors the temperature
of the coolant in the engine cooling system. After starting
the telehandler, allow time for the indicator to display a
temperature close to the normal range before operating the
telehandler. After the engine has sufficiently been warmed
up, normal engine coolant temperature should read between
180 to 2050F. The Engine Coolant Temp Indicator turns yellow
at coolant temperatures between 205 and 2150F to warn
that the engine operates at higher than normal temperature.
The Engine Coolant Temp Indicator becomes red when the
temperature reaches 2160F, indicating an engine overheating
situation.
P. BATTERY VOLTAGE INDICATOR
The Battery Voltage Indicator monitors the amount of charge
in Volts (V). The normal system voltage for the 12V system is
between 12.5 and 14 V. The indicator turns yellow if the charge
is between 11.5 and 12.5 V, and becomes red if the charge
drops below 11.5V. If the voltage indicator shows abnormal
readings (below 11.5V), stop the telehandler, follow proper
shut down procedures, tag telehandler with “Do Not Operate”
tags, and have a qualified mechanic service or repair the
telehandler BEFORE placing it into service again. The machine
has an additional 24V circuits for the starter and alternator.
Q. MENU BUTTON
The MENU button brings up the MAIN MENU on the screen.
R. HOUR METER
Indicates and records engine operating hours. Use the Hour
meter to establish a telehandler maintenance schedule.
