background image

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
     
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 
WARNING

 

-

 

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE   

                        THE FOLLOWING: 

 

ƒ

Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer 

 

PRODUCT: 

Do not remove permanently affixed labels, warnings, or plates from the product.    This may void the warranty. 

Do not try to alter the hood 
 

INSTALLATION

:

 

The installation in this manual is intended for qualified installers, service technicians or persons with similar 

qualified background.    Installation and electrical wiring must be done by qualified professionals and in accordance with all 
applicable codes and standards, including fire-rated construction.  When cutting or drilling into wall or ceiling; do not 
damage electrical wiring and other utilities.  Due to the size and weight of this range hood, two people installation is 
recommended.  Range hood may have very sharp edges; please wear protective gloves if it is necessary to remove any 
parts for installing, cleaning or servicing. 
 

VENTTING: 

For kitchen range or cook top ventilating use only.    DO NOT use to exhaust hazardous or explosive materials 

and vapors.  Ducted fans MUST always be vented to the outdoors.  DO NOT vent exhaust into spaces between walls, 
crawl spaces, ceiling, attics or garages.  Use only metal ductwork.  Old duct work should be cleaned or replaced if 
necessary to avoid the possibility of a grease fire.    Check all joints on duct work to insure proper connection and all joints 
should be properly taped. 

 
ELECTRICAL: 

All electrical wiring must be properly installed, insulated and grounded.  Before servicing or cleaning unit, 

turn power OFF and un-plugged   

 
OPERATION: 

Use high settings on cooking range only when necessary.  Keep all fan, baffle, spaces, filter, grease 

tunnel, oil container and grease-laden surfaces clean.  Grease should not be allowed to accumulate on fan, baffle, 
spaces, filter, grease tunnel, and oil container.    Never allow the filters to become blocked or clogged. Do not allow foreign 
objects, such as cigarettes or napkins, to be sucked into the hood. 

 
WARNING: 

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: 

 Never leave surface units unattended at high settings.    Boilovers cause smoking and greasy spillovers   

    that may ignite.    Heat oils slowly on low or medium settings. 

       

 Always turn hood ON when cooking at high heat or when greasy food. 

       

 Clean ventilating fans frequently.    Grease should not be allowed to accumulate on fan or filter. 

       

 Use proper pan size. Always use cookware appropriate for the size of the surface element.

 

 
WARNING: 

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE,   

            OBSERVE THE FOLLOWING: 
       

 

SMOTHER FLAMES

 with a close fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful   

            to prevent burns. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. 
       

 NEVER PICK UP A FLAMING PAN - you may be burned. 

       

 DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result. 

       

 Use an extinguisher ONLY if: 

            – You know you have a class ABC extinguisher, and you already know how to operate it. 
            – The fire is small and contained in the area where it started. 
      – The fire department is being called. 
            – You can fight the fire with your back to an exit. 

 

 

IMPORTANT SAFETY INSTRUCTIONS-continue

                                                 

www.XtremeAirUsa.com

                                                                    PAGE 

3

 

Summary of Contents for PRO-X PX01-I36













Reviews: