background image

www.XtremeAirUsa.com

                                                                    PAGE 

8

 

 

    RANGE HOOD OPERATION 

 

BEFORE YOU BEGIN

 (important): this machine is equipped with TOUCH SENSITIVE CONTROL, so please 

                        1.    DO NOT PRESS. Only TOUCH & HOLD DOWN 2 SECONDS for every change makes. 
            2.  TOUCH A WHOLE BUTTON only, please see below picture wrong vs. right 

 
 
 
 
 
 
 
 
 
 
 
 
 

1. TYPE 1: TOUCH SCREEN CONTROL (not for PX11 models) 

 
 
 

1. TYPE 1: TOUCH SCREEN CONTROL (FOR PX02- models   ONLY) 

 
 
 
 
 
 
 
 
 
 
 

Note: This range hood is equipped with remote control and smoke sensor that will self-calibrate within 5 seconds 
when the range hood is first electrically activated. Self-calibration will be set when the range hood beeps. LCD panel 
will turn off automatically after a period of inactivity.   

 

A. Activating Normal Blower Function: 

 
 

 
 
 

 

B. Activating Light Function: 

 

 
C. Activating Power-Off Delay Function: 

 

RIGHT: a whole button is   
       covered by a finger 

WRONG: Only half of a button   
        is covered by a finger 

RIGHT 

VS.

WRONG 

 

• While the range hood is off,   
                    Touch 

(+) to start from lowest speed, F1 

                   

Touch 

(-) to start from Highest speed, F4 

Touch (+) or (-) again to change the blower speed as indicated in LCD panel 

 

00 = blower off 
F1 = quiet speed 
F2 = low speed 
F3 = medium speed 
F4 = high speed 

• Touch 

Light 

button to turn the lights on or off.   

1.

 

While the range hood is on and the blower is running in normal mode, touch 

Power-Off Delay 

button to activate delay off timer.   

2.

 

Adjust to desired period of delay of timer by touching (-)

 

or (+)

 

button (1-15 minutes). Timer 

begins to countdown immediately, when it reaches 0, the blower will shut off.

 

10 

Summary of Contents for PRO-X PX10-U30













Reviews: