background image

 

www.XtremeAirUsa.com

                                                                    PAGE 

6

 

 

 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

 
 
 
IMPORTANT:    BEFORE YOU BEGIN 

 

1.

 

For TOUCH SENSITIVE CONTROLS, please DO NOT PRESS.    A light touch and hold on the required button for a matter of a (1) one second is all that is 
needed.

 

2.

 

T

OUCH THE ENTIRE BUTTON: See illustration on right:

 

 

 
 
 
 
 

1.    FOR PX10 & PX12 Model: 

TYPE 1: TOUCH SCREEN CONTROL PANEL   

 

 

 
 

 
 
 
 
 
 

Importance Notice: 

1.  AUTO FUNCTION ACTIVE: Once “Auto Function” is on or touched, all other functions will be DE-ACTIVATED and will NOT be 

working. 

2.  2 ½ HOUR AUTOMATIC SHUT OFF: This range hood will be shut off for every approx. 2 ½ hours.    You can re-start operation   
      usual after it was shut off. 
3.  SCREEN TURN OFF:    This range hood is equipped with remote control and smoke sensor that will self-calibrate within 5 seconds   
    when the range hood is first electrically activated. Self-calibration will be set when the range hood beeps. LCD panel WILL TURN       
    OFF automatically after a period of inactivity and every time when plugged into electrical outlet.   

 

A.    A

CTIVATING 

N

ORMAL 

B

LOWER 

F

UNCTION

While the range hood is off,   
                    Touch 

(+) to start from lowest speed, F1 

                   

Touch 

(-) to start from Highest speed, F4 

Touch (+) or (-) again to change the blower speed as indicated in LCD panel 

 
B.    Activating Light Function: 

 
Touch 

Light 

button to turn the lights on or off.   

 

10. RANGE HOOD OPERATION 

 

 

Figure 1 

Figure 2 

 

Figure 1A 

Figure 2A 

STEP 6: INSTALL & REMOVE BAFFLE FILTERS 

Refer to picture at left for the following steps:   
1.    Angle baffle filter toward front of hood or control side Figure 1 & 1A 
2.    Lift a baffle filter up above horizontal level then slide forward into       
        slot behind the front of hood Figure 2 & 2A

 

3.    Slide the installed baffle filter to either left or right until it stops.

 

4.    Repeat step 1 to 3 to install the next one, slide it opposite direction 
from the previous installed filter. 

 

NOTE:  The  middle  filter  has  to  be  installed  last  where  it 
should  be  taken  out  first  when  you  want  to  remove  other 
filters. 

 
To remove the baffle, please reverse the process.   
 

For best results, Start the range hood before 
cooking and allow it to operate several minutes 
after the cooking is completed to clear all smoke 
and odors from the kitchen.

   

 

 

 

00 = blower off 
F1 = quiet speed 
F2 = low speed 
F3 = medium speed 
F4 = high speed 

 

 

 

 

 

INCORRECT 

VS. 

Button is NOT completely covered

Entire button covered and lightly touched. 

 

CORRECT 

Summary of Contents for PX07-I36










Reviews: