7
C. Activating Power-Off Delay Function:
1. While the range hood is on and the blower is running in normal mode, touch
Power-Off Delay
button to activate delay off timer.
2.
Adjust to desired period of delay of timer by touching (-)
or (+)
button quickly (1-15 minutes). Timer begins to countdown immediately, when it
reaches 0, the blower will shut off.
3.
Display screen will show flashing clock if timer is working.
D. Activating Smoke Detector Function:
While the machine is off, touch
Auto Function
button to activate the smoke detector auto function mode.
NOTE: this function will only worked when there’s a lot of smoke. Once this button is touched, all other buttons are not active.
E. Changing the clock (only available in some models)
While the blower is off:
1. Touch power sign once. The hour indicator will be flashing.
2. Use (+) or (-) to adjust to the desired hour.
3. Touch power sign again for the “minutes”. Indicator will be flashing.
4. Use (+) or (-) to adjust to desired minutes.
5. Touch power sign again to clear the screen. Touch light button to validate. To check time, touch light button.
NOTE: The clock display is only available for product manufactured after October 2013.
F. Remote Control Sensor:
1.
Remote control sensor receives infrared (IR) signal from the remote control. The maximum distance for IR data transmission is 10
feet and requires direct line of sight. The transmission distance may vary depending on temperature and remote control battery
condition.
2. Light settings are independent from other settings (including power-off delay) and lights have to be manually turned on or off.
3.
The system saves user configurations, settings such as light, timer and blower (motor) speed will remain the same the next time it is
turned on.
PX07-I36 & PX06-I42
PX07-I48
Body Design
Non-Magnetic 1.0 mm Stainless Steel, Satin Finish
Non-Magnetic 1.0 mm Stainless Steel, Satin Finish
Power Rating
120V/60Hz (USA & Canada standard)
120V/60Hz (USA & Canada standard)
General Input Power
158W (150W + 4x2W)
308W (150W + 4x2W)
Motor Input Power
150 W each
150 W each
Ampere
1.3 A
2.6 A
Levels Of Speed Control
4 Levels
4 Levels
Maximum Airflow
900CFM
1600CFM
Noise Level
Approximately 1.5 – 6.0 sones or 33 – 54 dB
Approximately 3.0 – 7.0 sones or 41 – 56 dB
Number Of Motors
Single Motor
2motors
Motor Type
Single Chamber Ultra Quiet
Single Chamber Ultra Quiet
Fan Type
Squirrel Cage blower
2 Squirrel Cage blowers
Filtration Type
Heavy Duty Stainless Steel Baffle Filter
Heavy Duty Stainless Steel Baffle Filter
Illumination
4 LED lights, 2W Maximum/each
4 LED lights, 2W Maximum/each
Venting Size
Top 6 inches Round
Top 8 inches Round
Interference Protection
Radio Frequency Interference Protected
Radio Frequency Interference Protected
Note
Specification subject to change without notice.
Specification subject to change without notice.
1. If the range hood or lights does not operate after installation:
Check if the range hood has been plugged in. Make sure that all power has been turned back ON.
Swap out light assembly to working ones to deter mine whether it is caused by defective bulbs.
2. The range hood vibrates when the blower is on:
The range hood might not have been secured properly to the cabinet or wall.
Check if the blower wheel is damaged.
11. SPECIFICATION
12. TROUBLESHOOTING
A.Make sure the range hood is unplugged or turn OFF breaker.
B.Pop out the light by pressing behind the light fixture.
C.Install new light bulb.
D.Put the light set back by pressing it in.
E.Plug in and range hood to test for operation.
