background image

T

he 

A-Frame

 

ladder

 

must

 

be

 

fixed

 

on

 

the

 

edge

 

of

 

the

 

pool.

 

First,

 

align

 

the

 

two

 

holes

 

on

 

the

 

surface

 

of

 

the

 

deck

 

platform

 

with

 

the

 

edge

 

of

 

the

 

pool,

 

mark

 

the

 

hole

 

positions

 

at

 

the

 

edge

 

of

 

the

 

pool

 

with

 

a

 

fine

 

marker

 

pen,

 

then

 

drill

 

through

 

the

 

edge

 

of

 

the

 

swimming

 

pool

 

with

 

a

 

5

 

/

 

16

 

"drill

 

bit,

 

and

 

finally

 

use

 

bolts,

 

nuts

 

and

 

washers

 

to

 

fix

 

the

 

ladder

 

on the

 

edge

 

of

 

the

 

swimming

 

pool.

Routine

 

Maintenance

When

 

the

 

swimming

 

pool

 

is

 

not

 

in

 

use,

 

it

 

is

 

recommended

 

to

 

flip

 

the

 

outer

 

ladder

 

upwards,

 

then

 

push

 

it

 

down

 

and fix

 

it.

Deck Platform

Pool Edge

Bolt

9

If your pool height is 48", use the 2.5 bolt 5862050000 screw kit. 
If your pool height is 

52

", use the 5 bolt 5862050000

screw kit.

If your pool height is 54", use the 5 bolt 5862050001 screw kit. 

 

2. When removing the ladder, it is recommended to wash the ladder with soapy 

     

water to remove and debris. 

1. In cold weather and/or wintertime, remove the ladder and store it in a clean, dry 

place. 

Summary of Contents for 75136














Reviews: