background image

PRODUCT INFORMATION

5

INSTALLATION

• The standby switch located at the center right hand side of the fire must be first switch on.

• It takes some time for the receiver to respond to the transmitter. Do not 

PRESS

 the buttons more than once 

within two seconds for correct operation.

• Press once the button 

ON/OFF

 on the remote control this turns 

ON/OFF 

the appliance and fire effect.

• Pres

s the 

DIMMER

 button for operates the dimmer mode. Each time the dimmer button is Pressed, the intensity 

of the flame decrease. There are 5 brightness levels you can cycle through and the 

OFF

 setting.

• Press once t

he 

HEAT

 button for the low heat setting(750W); press twice for the high heat setting (1500W); 

press again to turn off the heater.

• Tem

perature setting. The highest temperature of the thermostat is 82F. There are several thermostat levels you 

can cycle through between 62F and 82F, and the 

OFF

 settings.

• Timer setting. Press 

the 

TIMER

 button to cycle through the timer settings (1Hour, 2H, 3H, 4H, 5H, 6H, 7H and 

8H) and the 

OFF

 setting.

• Colorful Setting. Press the remotes’ Colorful button, it can change the flame color. Press the first time, it will 

change from 

AMBER

 color to Blue color. Press the second Time, it will change from Blue to 

AMBER & BLUE

 

color. Press the third time, it willCome back to amber color.

REMOTE CONTROL

Remote control requires two 

AAA batteries

6

Summary of Contents for 95032










Reviews: