Xvent MiracleAir 300-A1 Instructions For Use And Installation Download

Page: 13 / 26

Version 1 – GBR (05/05/2020)

D-502-0173

3.2.3.

Installation of air purifier - MiracleAir 400-B units

No further installation is required after unpacking and positioning Miracleair filter unit.

3.3.

Electrical installation - connection to the electrical network

3.3.1.

General information - safety

Before starting the installation, make sure that the mains socket you intend to use to connect the unit
is equipped with a protective contact (pin).

The mains plug must always remain accessible

so that the unit may be safely disconnected from the

mains in the event of danger.

Verify that the outlet meets power requirements of the unit (voltage, current, frequency etc.) listed on
the production plate of the unit.

The relevant circuit must be protected in the power supply to maximum of 16 A.

The mains cable must not be broken.

Local electrical regulations must always be observed

When handling the unit, disconnect the device from the mains first (pull out the mains socket)

It is forbidden to tamper with the internal wiring of the unit in any way

This unit belongs to the product group with type Y connection. If the mains cable is damaged, it must
be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a
high-risk situations.

The supply voltage to the fan 1~230V / 50-60Hz must not be altered in any way. Otherwise there is a
risk of damage to the unit fan.

3.3.2.

Mains connection

the unit is supplied with a power supply cable with a flex plug with a protective contact. The length of the
mains cable is 2.7 m.

The unit is equipped with a 1-pole mains switch, which can be used to switch the power supply on and
off.

Connecting the unit to the mains does not require any further electrical connections, interconnections.

3.3.3.

Labelling of electrical parameters

all electrical parameters of the unit are shown on the production label

Fig. 11

Type: product type

Voltage (U): XXX V AC Frequency (f): XX/XX Hz
Current (I): XXX A

Weight (m): XX kg

Input (P): XXX W

IP:

Serial number

MADE IN CZECH REPUBLIC

EAN of the product

Summary of Contents for MiracleAir 300-A1



























Search results

Summary of Contents for MiracleAir 300-A1

Reviews:

Related manuals for MiracleAir 300-A1

Brands by name

Popular brands

Xvent MiracleAir 300-A1, Instructions For Use And Installation

Search results

Summary of Contents for MiracleAir 300-A1

Reviews:

Related manuals for MiracleAir 300-A1

Brands by name

Popular brands