background image

FCML 412 N(-S), FCML 412-M12

Safety

7

ba77197e02

01/2024

2.2

Safe operation

2.2.1 Authorized use

The authorized use of the FCML 412 N(-S), FCML 412-M12 is the stationary 

measurement of chlorine in drinking water, swimming pool water and process 

water. Only the operation and running of the product according to the instruc

-

tions and technical specifications given in this operating manual is authorized 

(see chapter 7 T

ECHNICAL

 

DATA

). Any other use is considered unauthorized.

2.2.2 Requirements for safe operation

Note the following points for safe operation:

The product may only be operated according to the authorized use spec

-

ified above.

The product may only be supplied with power by the energy sources men

-

tioned in this operating manual.

The product may only be operated under the environmental conditions 

mentioned in this operating manual.

The product may not be opened.

2.2.3 Unauthorized use

The product must not be put into operation if:

it is visibly damaged (e.g. after being transported)

it was stored under adverse conditions for a lengthy period of time (storing 

conditions, see chapter 7 T

ECHNICAL

 

DATA

).

Summary of Contents for WTW FCML 412-M12 Series

























Reviews: