Yale 4600CL Series Installation Instructions Manual Download

Page: 14 / 16

80-9510-0088-000 06/19

4600CL Series

Installation Instructions

Cylindrical Lock

For technical support contact Yale

at 800.438.1951 x5033 or support@yalelocks.com

An ASSA ABLOY Group brand

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

Lever Installation & Removal

Cylinders & Miscellaneous

Push/Turn Button and Plain Levers

Removal:

Push release tool into release hole. Remove lever.

Install:

Slide lever over lever catch. Ensure lever will not pull off.

RELEASE

HOLE

LEVER

ASSEMBLY

RELEASE

TOOL

Cylinder Lever

Removal:

Rotate key 45° clockwise (from shed position). Push release tool
into release hole. Remove lever.

Install:

Rotate key 45° clockwise (from shed position). Slide lever over
lever catch. Ensure lever will not pull off.

Interchangeable Core Lever

Removal:

Rotate Control key clockwise approximately 15 degrees.
Remove core and tailpiece. Use flat blade screwdriver to pull
back lever catch. Remove lever.

Install:

Slide lever over lever catch. Ensure lever will not pull off.

KEY

LEVER

ASSEMBLY

RELEASE

HOLE

RELEASE

TOOL

LEVER CATCH

(Move in direction of arrow)

LEVER

ROSE

Summary of Contents for 4600CL Series

















Search results

Summary of Contents for 4600CL Series

Reviews:

Related manuals for 4600CL Series

Brands by name

Popular brands

Yale 4600CL Series, Installation Instructions Manual

Search results

Summary of Contents for 4600CL Series

Reviews:

Related manuals for 4600CL Series

Brands by name

Popular brands