background image

AYR-MOD-ZW3-4-MNL-0050

ISL-0000-00-000

We’re here to help, 24/7       1-855-213-5841      support@yalelock.com      

support.shopyalehome.com

Smart Module Installation 

Z-Wave Plus

 v2     Assure Lock

®

 2

      

Models: YRD410, YRD420, YRD430, YRD450, YRD420-F, YRD450-F 

   

If your lock is already installed, 
remove the batteries.

Insert the Yale Z-Wave Plus™ v2 
Smart Module into the battery 
compartment slot. 

Reinsert the batteries.

Open the Yale Access App and 
navigate to your lock model.

3a. Select ‘Lock Settings’.

3b. Select ‘Yale Smart Module’.

3c. Follow steps in the app 
to complete set-up.

To remove the Yale Z-Wave Plus™ v2 
smart module from your system, 
select the disconnect Z-Wave™ 
option from lock settings 
in the Yale Access App.

1

2

3

4

NOTE: Anytime you add or remove a Smart Module from your lock, the batteries must be removed.

Anytime you add or remove a 

Smart Module from your lock, 

the batteries must be removed

Smart Module Installation 

Z-Wave Plus

 v2    Assure Lock

®      

Models: YRD216, YRD226, YRD256, YRL226, YRL216

If your lock is already installed, 
remove the batteries.

Insert the Yale Z-Wave Plus™ v2 
Smart Module into the battery 
compartment slot. 

Reinsert the batteries.

If you have SmartStart enabled 
with your Z-Wave™ system, 
follow in-app prompts to add a 
new device. If you do not have 
SmartStart or are not sure, 
follow the steps below.

3a. Enter your locks master entry 
code, followed by the

3b. Press the 

7

 key followed by 

the

3c. Press the 

1

 key followed by 

the

To remove the Z-Wave Plus™ v2 
Smart Module from your system, 
open the smart home
or alarm app and follow the 
instructions for removing a device.

4a. Enter your locks master entry 
code, followed by the

4b. Press the 

7

 key followed by the

4c. Press the 

1

 key followed by the

1

2

3

4

Anytime you add or remove a 

Smart Module from your lock, 

the batteries must be removed

If prompted, 
scan QR code

Summary of Contents for Assure Lock 2





































































Reviews: