background image

Electric Chain Hoist CPE/F

18

Translation of the original

EC DECLARATION OF CONFORMITY

in accordance with Machinery Directive 2006/42/EC (Appendix II A)

We,

COLUMBUS McKINNON Industrial Products GmbH

D-42329 Wuppertal, Yale-Allee 30

hereby declare, that the design, construction and commercialized execution of the below mentioned machine complies with the essential 
health and safety requirements of the EC Machinery Directive. The validity of this declaration will cease in case of any modifi cation or 
supplement not being agreed with us previously.
Furthermore, validity of this declaration will cease in case that the machine will not be operated correctly and in accordance with the 
operating instructions and/or not be inspected regularly.

Machine description:

 

Electric chain hoist CPE /F 

 

Mod. CPE/F 16-8, Mod. CPE/F 20-8, Mod. CPE/F 25-5, 

 

Mod. CPE/F 30-5, Mod. CPE/F 32-4, Mod. CPE/F 40-4, 

 

Mod. CPE/F 50-2, Mod. CPE/F 75-1,6, Mod. CPE/F 100-2

 

Capacity 1.600 - 10.000 kg

Machine type:

 

Electric chain hoist

Serial number:

 

Serial numbers for the individual units are recorded

Relevant EC Directives:

 

EC Machinery Directive 2006/42/EC

 

Directive for electrical equipment 2006/95/EC

 

ROHS directive 2002/95/EC

 

WEEE directive 2002/96/EC

 

EMV directive 2004/108/EC

Transposed harmonised

 

standards in particular:

 ISO 

12100: 2010

 EN 

349:1993+A1:2008

 EN 

818-1:1996+A1:2008

 EN 

818-7 : 2002+A1:2008

 EN 

14492-2:2008

 EN 

60204-32 :1999

 EN 

61000-6-2:2005

Transposed (either complete

 

or in 

extracts) national standards and 

 

technical specifi cations in particular:

 

DIN 15018-1:1984, DIN 15400:1990, DIN 15404-1:1989

 

BGV D6, BGV D8

Quality assurance:

 

EN ISO 9001: 2008

Authorised representative for technical data:

  COLUMBUS McKINNON Industrial Products GmbH

 

Yale-Allee 30 - D-42329 Wuppertal, Germany

Summary of Contents for CPEF





















Reviews: