background image

13

14

SINGLE & DOUBLE GIRDER TOP-RUNNING BRIDGES

WITH INDIVIDUAL MOTOR DRIVEN

END TRUCKS

P/N: 11532620   REV. AA

   September 2018

WARNING

NON-FACTORY AUTHORIZATIONS OR MODIFICATION 

OF EQUIPMENT AND USE OF NON-FACTORY REPAIR 

PARTS CAN LEAD TO DANGEROUS OPERATION AND 

INJURY.

TO AVOID INJURY:

Do not alter or modify equipment without factory  

 

authorization.

Do use only factory provided replacement parts.

The numbers assigned to the parts of the various assemblies in 

the parts lists, may not be the part numbers used in manufacturing 

the part. They are identification numbers, that when given with the 

catalog number permits us to identify, select or manufacture, and 

ship the correct part needed.

REPLACEMENT PARTS

The following parts lists and illustrations cover standard model 

cranes. Typical units are used as the basis for the exploded parts 

illustrations; therefore, certain variations may occur from the parts 

information given. For this reason always give the catalog number, 

sales order number, model number, motor horsepower, voltage, 

phase and frequency when ordering replacement parts. For motors, 

gear cases and electrical components, give complete nameplate data.

WARNING

Using "commercial" or other manufacturer's parts to repair 

the Yale Hoist may cause load loss.

TO AVOID INJURY:

Use only Yale supplied replacement parts. Parts may 

look alike but Yale parts are made of specific materials or 

processed to achieve specific properties

ORDERING INSTRUCTIONS

The following information must accompany all correspondence 

orders for replacement parts:

1.  Hoist Model Number from identification plate.

2.  Serial number of the hoist stamped below identification 

plate.

3.  Voltage, phase, hertz from the identification plate.

4.  Length of lift.

5.  Part number of part from parts list.

6.  Number of parts required.

7.  Part name from parts list.

NOTE: 

When ordering replacement parts, it is recommended that 

consideration be given to the need for also ordering such items as 

gaskets, fasteners, insulators, etc. These items may  be damaged 

or lost during disassembly or just unfit for future use because of 

deterioration from age or service.

MAINTENANCE CONTINUED

NOTES

CMK_12322 Yale Rotating Axle End Truck Parts 11532619-REV AD_mec.indd   14

10/16/18   2:07 PM

Summary of Contents for Shaw-Box SK

























Reviews: