Digital Lock Set
SL7100 Series
Assembly
4) Handing the Digital Interior Handle
6) Positioning the Spindles
2) Apply the Template
B
of the Digital Code Pad
longer spindle (86mm) or (100mm).
spindle length to suit the door thickness.
door thinknesses of 35-50mm use the
* Position spindle centrally through the
use the shorter spindle (76mm). For
* For door thinknesses less than 35mm
Three spindles are provided. Select the
hung door and Hole B for
Assembly. Hole A for left hand
latch hub to suit door handing as shown.
Support Post
Latchbolt
Hex Screw
A
right hand hung door.
backset line to suit the deadlatch assembly supplied.Tape the template to the door.
Select the desired position on the door. Fold the template on the dotted 60mm
Support Post in the back
Fit the Latch Assembly
Fit Hex screw post top and
bottom of external keypad.
* Fit the latch assembly with 2 wood screws.
(Ensure that the bevelled face of
* Remove the latch and cut a 3mm rebate so that the face plate fits flush with the
* Mark the central point on the "centre line of latch" on the edge of the door and
5) Fit Latch Support Post
the latchbolt faces the door frame)
* Insert the latch into the latch holes and mark around the face plate.
drill a 25mm hole to a depth of 85mm.
* Mark and drill six 10mm holes as shown on the template.
edge of the door.
(HOLE B)
Assembly
Interior Handle
Hexagon Socket
Head Cap Screw
BLACK HANDING
SCREWS
(HOLE A)
screw from hole A and
and Hole B for right hand hung
Hole A for left hand hung door
Check correct lever handle function by turning handle from
horizontal position through 90° without resistance
* Loosen the Hexagon Socket
To change for a left hand door:
Head Cap Screw located at the bottom of the spindle hub and
rotate the lever handle from right to left.
* Tightening the Hexagon Socket Head Cap Screw and make sure
the lever handle is horizontal.
LEVEL
HANDLE
Rotation
door.
relocate it in hole B.
To change lever handle to suit
a left hand :
* Remove BLACK handling
HANDLE
Rotation
Pad Assembly
3) Handing the Digital Exterior Code
HANDLE
Viewed from
the outside
SPINDLE SHOULD ENGAGE
DOOR HUNG ON RIGHT
THE LATCH AS ABOVE
SPINDLE SHOULD ENGAGE
THE LATCH AS ABOVE
DOOR HUNG ON LEFT
Apply strength to rotate the handle to the
desired direction.
IMPORTANT: In order to change the left
the lock must be mounted on the door.
and right hand of the lock handles correctly,
Post
* Fit strike plate and strike box using only one wood screw at first to ensure that it is positioned accurately.
position, followed by a passage knob of Digital Interior Handle
* Turn handle of Digital Exterior Code Pad Assembly to the 6 o'clock
Assembly to the 12 o'clock position.
Mode" is set. Then you do not need a code and you can open the door.
o'clock to 9 o'clock “P” position. Release the handle and "Passage
* Turn the passage knob of Digital Interior Handle Assembly from 12
Assembly to 6 o'clock position and hold the handle in downward
* Enter correct codes turn the handle of Digital Exterior Code Pad
TO SET PASSAGE MODE - FREE ACCESS AND EGRESS.
Digital Lock Set - Passage Mode Function
* When correctly positioned secure with the second wood screw and check lock set for smooth operation.
* The latchbolt and not the deadlatch pin should enter the strike plate aperture freely and engage without excessive play.
TO SET CANCEL PASSAGE MODE -
Passage Function - where fitted
passage knob position.
* Drill and chisel out the latchbolt hole to accommodate the latch bolt strike box(Fig 3).
* Cut a 1mm deep rebate so that the strike plate fits flush with door jamb(Fig 2).
* Using the strike plate as a template,align it with the position marks in the jamb and mark the inner and outer edges of
* Close the door and mark the position of the strike plate on the door jamb.
* Position the strike plate on the door so that it fits against the flat of the latchbolt,with deadlatch pin depressed (Fig. 1).
* Close the door against the door frame and transfer the centre of the latchbolt onto the jamb.
* Before tightening of fixing screws make sure the lock is vertical. Test the
mechanism to ensure that the lock functions correctly and moves easily.
NOTE:
DO NOT overtighten the fixing screws-this may cause distortion and
CHECK THAT THE CODE WORKS TO AVOID A LOCKOUT BEFORE
CLOSING THE DOOR.
Handle Assemblies.
* Hold the Exterior Code Pad Assembly onto the door with the spindle
* Fit the neoprene seals to both the Exterior Code Pad and Interior
* For door thinknesses less than 48mm use the shorter fixing screws (36mm).
Select the fixing screws to suit the door thinkness.
in position and ensuring that the latch support post engages the hole
in the latch assembly.
* Locate the Interior Handle Assembly on the inside of the door engaging
* Screw both sides together with fixing screws top and bottom. (FIG 1)
the spindle in the handle hub.
Fig. 3
the strike plate on the jamb.(Fig 2).
Fig. 1
Fig. 2
8) Fitting the Strike Plate
FIG 1
lead to poor operation.
7) Mounting the Lock
DEADLATCH
PIN
"LATCHBOLT"
Digital Lock Set
Installation Instructions
Digital Lock Set
Installation Instructions
