YAMABISHI ALS Series Instruction Manual Download | Manualshive

Page: 13 / 17

background image

３

.

Functions

−

Self-Diagnosis of Battery

−

Push a TEST Key about two seconds at the inverter operating.

Self-diagnosis of Battery is done.
If there is no wrong point, after ten seconds it is returned to the inverter
operating.
If there are a few amounts of battery, an alarm rings, and it is returned to
the inverter operating soon.

−

Turn to Bypass

−

Push an ON/ OFF Key at the inverter operating, it is returned to bypass
operating.
Push an ON/ OFF Key at the bypass operating, it is returned to inverter
operating after fifteen seconds.
It isn't returned to the inverter operating at the over-electric current
time and so on.

１２

«
...
11
12
13
14
15
...
»

Summary of Contents for ALS Series


















Reviews:

No comments

Related manuals for ALS Series

Brand: Tripp Lite Pages: 4

Brand: IBM Pages: 84

Brand: Salicru Pages: 72

Minuteman Encompass EC1000RT2U

Brand: Para systems Pages: 16

Brand: Eaton Pages: 23

Brand: Virginia Controls Pages: 17

5SC 1000i Rack2U

Brand: Eaton Pages: 20

Brand: Eaton Pages: 28

Brand: Powervar Pages: 66

Inverter Series IS1050

Brand: OPTI-UPS Pages: 1

Brand: X-TREME Pages: 40

Brand: V7 Pages: 22

Brand: Digitus Pages: 81

Brand: LESTAR Pages: 2

Brand: Eaton Pages: 42

Brand: Eaton Pages: 34

Protect 3.M 2.0

Brand: AEG Pages: 4

Brand: CyberPower Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands