background image

 

1

 / 

3

 

 

 

- Preface

     

 

Thank you very much for purchasing Yamada Pump. This machine is a portable type lubricator that is indispensable 
for grease lubrication for machines and vehicles. This lubricator cannot be used for oil lubrication. The applicable 
grease is limited to a type of NLGI No.0 or less in the normal operating conditions. If the lubricator is used in an 
extremely cold or low-temperature environment, the discharge volume will be remarkably lowered. Silicone grease is 
not applicable. 
 

-  For Safe Operation 

This document describes the items that are important for the user to operate this product safety, correctly, and 
efficiently. Before operating this product, read this manual thoroughly, in particular, “Warnings and Cautions” at the 
beginning of this manual, with a good understanding of its contents. Keep this manual carefully in an easy-to-access 
place so that the user may refer to it whenever necessary. 
 

-  Warnings and Cautions 

To use this product safely, be sure to observe the contents of the following description. In this manual, warnings and 
cautions are indicated by using symbols. These symbols are intended to prevent death or serious injury that may be 
caused to the operator or those who are around the product and damage that may be caused to the articles that are 
around the product, as well as to use the product safely and correctly. Each symbol is indicated and has a meaning as 
shown below. Read the description with a good understanding of its contents. 
 

WARNING :

 

This indicates the existence of potential hazard which, if not avoided, will 

result in death or serious injury. 

CAUTION : 

This indicates the existence of potential hazard which, if not avoided, may 

result in bodily injury or in physical damage. 

To indicate the contents of danger and damage, the following symbols are used together with the above indications. 

 

This symbol indicates an act that is prohibited (prohibition). The concrete contents of prohibition are 
indicated by the side of the indication. 

 

This symbol indicates the contents that must be observed. The concrete contents of observance are 
indicated by the side of the indication. 

 
 
 

Summary of Contents for SKR-55 880870



















Reviews: