background image

Operation

30

If equipped with a portable fuel tank
1.

Pour oil into the portable fuel tank, and
then add gasoline.

2.

Replace the fuel tank cap and close tight-
ly.

3.

Shake the fuel tank to mix the fuel thor-
oughly.

4.

Make sure that the oil and gasoline are
mixed.

If equipped with a built-in fuel tank
1.

Pour oil into a clean fuel can, and then
add gasoline.

2.

Replace the fuel can cap and close tight-
ly.

3.

Shake the fuel can to mix the fuel thor-
oughly.

4.

Make sure that the oil and gasoline are
mixed.

5.

Pour the gasoline and oil mixture into the
built-in fuel tank.

TIP:

If using a permanently installed tank, pour the
oil gradually as the gasoline is being added to
the tank.

EMU27451

Operating engine

EMU27466

Sending fuel (portable tank)

WARNING

EWM00420

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the
water near you.

When the air vent screw is loosened,
gasoline vapor will be released. Gaso-
line is highly flammable, and its vapors
are flammable and explosive. Refrain
from smoking, and keep away from
open flames and sparks while loosening
the air vent screw.

This product emits exhaust gases which
contain carbon monoxide, a colorless,
odorless gas which could cause brain
damage or death when inhaled. Symp-
toms include nausea, dizziness, and

1.

: Gasoline

2.

: Engine oil

1. Engine oil
2. Gasoline

100:1

1 L

(0.26 US gal, 

0.22 Imp gal)

12 L

(3.2 US gal, 

2.6 Imp gal)

14 L

(3.7 US gal, 

3.1 Imp gal)

24 L

(6.3 US gal, 

5.3 Imp gal)

0.01 L

(0.01 US qt, 

0.01 Imp qt)

0.12 L

(0.13 US qt, 

0.11 Imp qt)

0.14 L

(0.15 US qt, 

0.12 Imp qt)

0.24 L

(0.25 US qt, 

0.21 Imp qt)

ZMU04910

U63V1EE0.book  Page 30  Tuesday, March 3, 2009  10:50 AM

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for 15









































































Reviews: