30
Distortion Multi (Phaser)
Multi effect consisting of Comp + Dist Delay + Reverb. Mainly used for direct connection to guitar
amp’s front input.
Parameter
Display
Range
Description
Type
TYPE
Lead1, Lead2, Drive1, Drive2,
Crunch1, Crunch2, Fuzz1,
Fuzz2, Distortion1, Distortion2,
Overdrive1, Overdrive2, Tube,
Solidstate, Bypass
Distortion type
Gain
GAIN
0.0 to 10.0
Adjusts the amount of distortion
Master
MSTR
0.0 to 10.0
Adjusts the volume
Tone
TONE
0.0 to 10.0
Adjusts the tone
EQ 1 Freq.
EQ1F
50.0 to 400 Hz
Specifies the post effect EQ1 frequency
EQ 1 Gain
EQ1G
-12.0 to 12.0 dB
Specifies the post effect EQ1 gain
EQ 1 Q
EQ1Q
0.100 to 20.0
Specifies the post effect EQ1 Q (bandwidth)
EQ 2 Freq.
EQ2F
200 to 1.6 kHz
Specifies the post effect EQ2 frequency
EQ 2 Gain
EQ2G
-12.0 to 12.0 dB
Specifies the post effect EQ2 gain
EQ 2 Q
EQ2Q
0.100 to 20.0
Specifies the post effect EQ2 Q (bandwidth)
EQ 3 Freq.
EQ3F
600 to 4.80 kHz
Specifies the post effect EQ3 frequency
EQ 3 Gain
EQ3G
-12.0 to 12.0 dB
Specifies the post effect EQ3 gain
EQ 3 Q
EQ3Q
0.100 to 20.0
Specifies the post effect EQ3 Q (bandwidth)
EQ 4 Freq.
EQ4F
2.00 k to 16.0 kHz
Specifies the post effect EQ4 frequency
EQ 4 Gain
EQ4G
-12.0 to 12.0 dB
Specifies the post effect EQ4 gain
EQ 4 Q
EQ4Q
0.100 to 20.0
Specifies the post effect EQ4 Q (bandwidth)
Pre EQ Level
PELV
0.0 to 10.0
Specifies the pre effect EQ level
Pre EQ 1 Freq.
PE1F
50.0 to 500 Hz
Specifies the pre effect EQ1 frequency
Pre EQ 1 Gain
PE1G
-12.0 to 12.0 dB
Specifies the pre effect EQ1 gain
Pre EQ 1 Q
PE1Q
0.100 to 20.0
Specifies the pre effect EQ1 Q (bandwidth)
Pre EQ 2 Freq.
PE2F
200 to 2.00 kHz
Specifies the pre effect EQ2 frequency
Pre EQ 2 Gain
PE2G
-12.0 to 12.0 dB
Specifies the pre effect EQ2 gain
Pre EQ 2 Q
PE2Q
0.100 to 20.0
Specifies the pre effect EQ2 Q (bandwidth)
Pre EQ 3 Freq.
PE3F
1.00 k to 10.0 kHz
Specifies the pre effect EQ3 frequency
Pre EQ 3 Gain
PE3G
-12.0 to 12.0 dB
Specifies the pre effect EQ3 gain
Pre EQ 3 Q
PE3Q
0.100 to 20.0
Specifies the pre effect EQ3 Q (bandwidth)
Comp. Threshold
CTHR
-54.0 to 0.0 dB
Level at which compressor activates
Comp. Ratio
CRAT
1:1 to
∞
:1
Compression ratio
Comp. Attack
CATT
0 to 120 ms
Time required for compressor to peak after exceeding threshold
Comp. Release
CREL
6 to 11500 ms
Time required for compressor to terminate after going below threshold
Comp. Knee
CKNE
Hard, 1 to 5
Adjusts the width of the gain curve just above the threshold
Comp. Gain
CGAI
0.0 to 18.0 dB
Output level
N. G. Threshold
NGTH
0.0 to 10.0
Level at which the noise gate activates
N. G. Attack
NGAT
0.0 to 120 ms
Time required for the noise gate to open after signal exceeds threshold
N. G. Hold
NGHL
0.02 to 2040 ms
Time noise gate stays open
N. G. Decay
NGDC
6 to 44500 ms
Time required for the noise gate to close after signal goes below thresh-
old
Wave
WAVE
Sine, Triangle
Modulation waveform
Phaser Speed
PHSP
0.0 to 10.0
Modulation speed
Phaser Depth
PHDP
0.0 to 10.0
Modulation depth
Phaser Feedback
PHFB
-99 to 99
Phaser feedback
Phaser Level
PHLV
0.0 to 10.0
Phaser level
FB. Delay
DTFB
0.0 to 1000.0 ms
Loop delay time
Tap L
DT.L
0 to 100 %
Left channel delay output time (see
Tap R
DT.R
0 to 100 %
Right channel delay output time (see
)
Delay FB. Gain
D.FB
-99 to 99
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
Delay High
D.HI
0.1 to 1.0
Delay high-frequency feedback ratio
Delay Level
DLVL
0.0 to 10.0
Delay level
High Pass Filter
DHPF
Thru to 8.00 kHz
High-pass filter cutoff frequency. For delay, reverb
Low Pass Filter
DLPF
50.0 Hz to Thru
Low-pass filter cutoff frequency. For delay, reverb
Reverb Ini. Delay
RIDL
0.0 to 500.0 ms
Initial delay before reverb begins
Reverb Time
RT
0.3 to 99.0 s
Reverb time
Reverb High
R.HI
0.1 to 1.0 ms
High-frequency reverb time ratio
Reverb Diffusion
RDIF
0 to 10
Left and right reverb spread
Reverb Density
RDNS
0 to 100
Reverb density
Reverb Level
RLVL
0.0 to 10.0
Reverb level
Summary of Contents for Acoustic
Page 1: ...EFFECT LIST...
Page 32: ...Printed in China WD92180...
