SETUP MENU
28
En
IP Setting
You can set IP Setting to Auto/Manual. When set to Auto,
IP address is allocated automatically by system. When set
to Manual, IP Address, Subnet Mask, Default Gateway
and DNS should be set manually.
Auto
*
, Manual
BD-Live Connection
You can set access restriction to BD-Live contents.
DLNA
You can set the DLNA (p. 19) to Enable/Disable. When
you do not use the DLNA function, set to Disable.
Enable
*
, Disable
Proxy Setting
You can set Proxy Setting. Set to Disable for normal use.
■
Display Setting
The default settings are marked with “
*
”.
TV
TV Screen
You can set the screen aspect ratio of the connected TV,
and adjust the video output.
If you switch your TV (i.e. because you have bought a
new one) and the screen aspect ratio of the connected TV
changes, you will have to change the TV Screen setting.
Resolution
You can select the video output resolution from Auto,
480i/576i, 480p/576p, 720p, 1080i, and 1080p. When set
to Auto, resolution is set to the maximum resolution
according to the connected TV. For more details on output
formats, refer to “About the video output formats” (p. 30).
Auto
*
, 480i/576i, 480p/576p, 720p, 1080i, 1080p
TV System
You can select TV System from PAL, NTSC and Multi.
Set the same TV System as your TV set. For more details
on output formats, refer to “About the video output
formats” (p. 30).
NTSC, PAL
*
, Multi
Note
– When no picture is displayed after this setting is
changed, press and hold
on the front panel for
around 5 seconds to switch NTSC/PAL manually.
Color Space
You can select the Color Space (p. 35) output from
HDMI. This function is available when this Player is
connected with an HDMI cable.
Note
– This function is only available on TVs that support
this function.
HDMI Deep Color
When your TV and/or AV receiver is compatible with
Deep Color (p. 35), set this item according to your TV/AV
receiver. This function is available when this Player is
connected with an HDMI cable.
30 bits, 36 bits, Off
*
HDMI 1080p 24Hz
This outputs the BD-Video encoded in 24Hz frame rate in
HDMI 1080p 24Hz. Smoother video playback may be
available with this function. This function is available
when your TV/AV receiver support this function, and this
Player is connected with an HDMI cable. For more details
on output formats, refer to “About the video output
formats” (p. 30).
On, Off
*
Permitted
*
Allows all BD-Live discs to connect the network.
Partial
Permitted
Allows only discs with owner certification.
Prohibited
Prohibits all BD-Live discs to connect the network.
Disable
*
Sets proxy server to disable. Select this item when
proxy server is not used.
Proxy Host
Sets the proxy host.
Proxy Port
Sets the proxy port.
16:9 Full
Select this when this Player is connected to a TV
with a 16:9 screen. When a 4:3 aspect ratio video is
played back, the video is displayed as shown below.
16:9 Normal
*
Select this when this Player is connected to a TV
with a 16:9 screen. When a 4:3 aspect ratio video is
played back, the video is displayed as shown below.
4:3 Pan Scan
Select this when this Player is connected to a TV
with a 4:3 screen. When a 16:9 aspect ratio video is
played back, the video is displayed as shown below.
4:3 Letterbox
Select this when this Player is connected to a TV
with a 4:3 screen. When a 16:9 aspect ratio video is
played back, the video is displayed as shown below.
Original
image size
On 16:9 (wide screen) TV
16:9 Full
16:9 Normal
4:3
Original
image size
On 4:3 TV
4:3 Pan Scan
4:3 Letterbox
16:9
RGB
Outputs video signal at normal signal range.
YCbCr
*
Sets Color Space to YCbCr.
YCbCr422
Sets Color Space to YCbCr422.
