Yamaha CS-R10, Systems Setup Manual

RIVAGE PM10 System Setup Guide

27

7

OMNI IN jacks

These are balanced XLR-3-31 female input jacks for 
inputting analog audio signals from line level devices 
or microphones. They feature SILK digital 
processing.

8

OMNI OUT jacks

These are balanced XLR-3-32 male output jacks that 
transmit analog audio signals.

9

AES/EBU jacks

Both input and output jacks feature built-in sampling 
rate converters.

IN

These are balanced XLR-3-31 female input jacks that 
accept digital audio signals in AES/EBU format.

OUT

These are balanced XLR-3-32 male output jacks for 
outputting digital audio signals in the AES/EBU 
format.

)

MY card slots

Install optional Mini-YGDAI I/O cards here to 
expand I/O ports.

!

USB ports

Use these ports to connect a USB storage device such 
as a flash drive, USB mouse, or USB keyboard.

@

WORD CLOCK OUT connector

This BNC connector is used to transmit word clock 
signal to an external device.

#

TO ENGINE OUT/IN connectors

These RJ-45 connectors allow the unit to be 
connected to a console network in a ring topology via 
Ethernet cables (CAT5e or higher recommended).

NOTE

• Use an STP (Shielded Twisted Pair) cable to prevent 

electromagnetic interference. Make sure that the metal 
parts of the plugs are electrically connected to the STP 
cable’s shield by conductive tape or comparable means.

• The use of Ethernet cables with Neutrik etherCON CAT5 

compatible RJ-45 plugs is recommended. Standard 
RJ45 plugs can also be used.

• Cable length can span up to 100 meters between 

devices. Maximum practical distance may vary 
depending on the cable used.

$

ERR indicator

This indicator lights up or flashes red if an error 
occurs.
In such an event, please contact your Yamaha dealer.

%

LINK indicator

This indicator flashes or lights up, depending on the 
network status.

^

TX/RX indicators

The appropriate indicator flashes green when data is 
transmitted from (TX) or received at (RX) the TO 
ENGINE OUT/IN connectors.

&

NETWORK connector 

This RJ-45 connector allows the unit to be connected 
to a computer via an Ethernet cable (CAT5e or higher 
recommended).

NOTE

• Use an STP (Shielded Twisted Pair) cable to prevent 

electromagnetic interference. Make sure that the metal 
parts of the plugs are electrically connected to the STP 
cable’s shield by conductive tape or comparable means.

• The use of Ethernet cables with Neutrik etherCON CAT5 

compatible RJ-45 plugs is recommended. Standard 
RJ45 plugs can also be used.

• Cable length can span up to 100 meters between 

devices. Maximum practical distance may vary 
depending on the cable used.

*

LINK/ACT indicator

This indicator flashes or lights up green, depending 
on the connection status.

(

Vent

The control surface is equipped with cooling fans. 
These vents let warm air out from the unit. Please 
make sure that you do not block the vents with any 
object.

Male XLR plug

1 (Ground)

3 (Cold)

2 (Hot)

Female XLR plug

2 (Hot)

3 (Cold)

1 (Ground)

Green 
(flashing)

The unit is preparing to connect to the 
console network. If it continues flashing, 
the system is not functioning properly. If 
the problem persists after you take the 
following actions, please contact your 
Yamaha dealer.
• Turn the power to the RIVAGE PM10 

system off and then on.

• Make sure that the cables are 

connected properly.

• Make sure that the cables are securely 

inserted (locked in).

• Change to a different cable. 

Green 
(lit steadily)

The unit is connected to the console 
network properly.