Yamaha CS6X Owner'S Manual Download

Page: 137 / 196

137

■

FMod (Filter Modulation Depth)

Set the amount by which the filter Cutoff frequency
changes when the controller (Source) is used.

❏

Settings:

0 ~ 127

■

AMod (Amplitude Modulation Depth)

Set the amount by which the amplitude modulation

changes when the controller (Source) is used.

❏

Settings:

0 ~ 127

Part Insertion Effect (A/D Input Part only)

You can set parameters for the Insertion Effects used
by the A/D Input Part. If you have selected the A/D
Input Part, as the InsEF (Insertion Effect) in the EFF
Part screen, the following screens will be available.

EFF EF1/2 (Insertion Effect 1/2)

Choose the type of effect used for the A/D Input Part.
You can select the Effect Category for Insertion Effect 1/2
with the Ctgry parameter and the Effect Type with the
Type parameter. After selecting the Effect Type, you can
start setting its parameters by pressing the [ENTER] key.

The connection between Insertion Effects 1 and 2 is fixed
as 1

➝

2 (Serial).

■

Ctgry (Effect Category)

Set the Category of the Effect. The first Effect Type

of the selected Category will blink.

❏

Settings:

Details are given in the Effect Types list of the
separate Data List.

■

Type (Effect Type)

Set the type of Effect. This depends on the selected
Category. For certain Categories, the Effect Type will
blink. In this case, you can press the [ENTER] key
to set the Effect Type.

❏

Settings:

Details are given in the Effect Types list of the
separate Data List.

■

Dry/Wet

Set the mix level of the wet signal (which has been
passed through the Effects Unit) and the dry signal
(which has not been passed through the Effects
Unit). This may be unavailable, depending on the
selected Effect Type.

❏

Settings:

D63>W ~ D=W ~ D<W63

EFFíEF1) Ctgry Type Dry/Wet [ENTER]
PartAD DLY:DelayLCR D<W63 to Edit

Effect Parameter Settings

These parameters are available when you press the
[ENTER] key for certain Effect Types.
Use the [PAGE] knob to switch between screens,
and use the other knobs and the [INC/YES] and
[DEC/NO] keys to set each parameter.
When you press the [EXIT] key, you will be
returned to the Effect Type selection screen.

The number of parameters and the contents of each
screen will vary depending on the selected Effect
Type. Details are given in the Effect Type list of the
separate Data List.

Zones (CS6x)

You can edit the zones used by Performances in Master
Keyboard Mode. Use Knob [A] (or BANK [A]~[D]
keys) to select the zone (1 to 4), then set the zone’s
parameters. The following eight screens are available
for Master Keyboard parameters.
You can choose zones if “4zone” has been selected as
the Mode at the GEN M.Kbd screen (Page 123), and if
the [MASTER KEYBOARD] key LED is lit.

• Master keyboard

MKB Transmit (Master Keyboard Transmit)
MKB Note (Master Keyboard Note)
MKB TxSw1 (Master Keyboard Transmit Switch 1)
MKB TxSw2 (Master Keyboard Transmit Switch 2)
MKB TxSw3 (Master Keyboard Transmit Switch 3)
MKB TxSw4 (Master Keyboard Transmit Switch 4)
MKB TxPreset1 (Master Keyboard Transmit Preset 1)
MKB TxPreset2 (Master Keyboard Transmit Preset 2)

EXIT

ENTER

SHIFT

PAGE

PART/ELEMENT

DATA

EFFíEF1) Delay Lch Cch Rch
PartAD 333.3 500.0 500.0 166.7

EFFíEF1) Ctgry Type Dry/Wet [ENTER]
PartAD DLY:DelayLCR D<W63 to Edit

Select Effect Type

Parameters