background image

 

DM2000/02R96/DM1000 Version2 System Software Installation Guide

 

5

 

ENGLISH

 

[DM2000 users]

 

Updating Flash Update

 

If you are using the DM2000, you must use the following 
procedure to update FLASH UPDATE (a portion of the system 
software) before you begin the installation. If you fail to update 
FLASH UPDATE first, system software installation may fail and 
the console may malfunction.

 

1

 

Make sure the power to the DM2000 is turned off, 
then insert the included SmartMedia disk 
(Firmware) into the card slot on the DM2000.

 

2

 

Turn on the power to the DM2000. After counting 
down, the DM2000 starts updating Flash Update.

 

The updating process takes about 30 seconds. When the 
update is complete, the DM2000 displays the usual screen. 
Install the system software.

 

Direct installation

 

If you can access the Internet directly from your computer, 
follow the steps below to install the software. See page 8 if you 
access the Internet from a different computer.

 

1

 

Start the computer and check to see if the 
following steps are complete.

 

• Installing the Yamaha USB-MIDI Driver in the 

computer (See the included Studio Manager Installation 
Guide.)

• Connecting the computer and the console using a USB 

cable

• Accessing the Internet from the computer
• Backing up the data in the user memories in the console 

(See the DM2000/02R96/DM1000 Owner’s Manual.)

• If you are using the DM2000, update the FLASH 

UPDATE

 

2

 

While holding down the following key on the 
console, turn on the power of the console.

 

Continue holding down the key until the display blinks 
“FLASH UPDATE.”

 

DM2000:

 

 Transport [REC] key

 

02R96:

 

 MACHINE CONTROL [REC] key

 

DM1000:

 

 MONITOR [CLEAR] key

 

3

 

Insert the included CD-ROM (Firmware) into the 
CD-ROM drive.

 

4

 

Locate the Upgrade folder on the CD-ROM (“Mac 
OS 9: Upgrade” for Mac OS 9; “Mac OS X: 
Upgrade” for Mac OS X), then copy the folder 
onto the hard disk.

 

Do not run the installer directly from the CD-ROM drive.

 

5

 

Double-click “DMUpgrade.exe” (or 
“****UpgradeE” for Mac OS) in the Upgrade folder 
that you copied to the hard disk.

 

The installer window opens.

 

6

 

Select [Install], then click [Next].

 

The following window opens.

 

Installation will initialize data in the DM2000’s user 
memories. Be sure to back up important data using MIDI 
Bulk Dump or Studio Manager (refer to the DM2000 
Owner’s Manual).

After you update Flash Update, install the system software. 
When you finish updating Flash Update, the DM2000 is 
temporarily unavailable for operation.

Do not turn off the power during the Flash Update updating 
process.

The installation procedure will initialize data in the user 
memories in the console. Be sure to back up important data 
using MIDI Bulk Dump or Studio Manager. (Refer to the 
DM2000/02R96/DM1000 Owner’s Manual.)

 

NOTE: 

 

The following instruction refers to installing the software in 

the 02R96 from a connected computer that runs Windows 98SE. 
However, the basic installation procedure also applies globally to any 
OS or console. Steps that vary with different operating systems will 
be explained separately.

 

NOTE: 

 

If an error message appears, refer to the Error Message list on 

page 10.

Summary of Contents for DM2000V2K














Reviews: