Yamaha DME64N - Pro Audio, Owner'S Manual

Ref

erences

Error Messages

DME64N/DME24N Owner’s Manual

58

Error Messages

Message

Meaning

Action

Error messages 

Cannot Select

No selectable items are available in the scene or 
monitoring point list display.

Make the appropriate settings via the DME Designer 
application.

Critical Battery

The internal battery is almost discharged. Your data may 
be lost.

If you turn off power to the unit, the current settings may 
be lost and reset to the default values. Stop operating the 
unit, and contact a Yamaha dealer for battery 
replacement.

Invalid Password

An invalid password has been entered.

Enter the correct password. If you have lost or forgotten 
your password, contact a Yamaha dealer.

Log Buffer Full

Saving is not possible, since the Event Log saving area is 
full. 

Use DME Designer to delete the log.

Low Battery

The backup battery voltage is low.

This does not affect the operation of the unit. However, if 
you continue using the unit, the settings may be lost and 
reset to the default values. Contact a Yamaha dealer for 
battery replacement at your earliest convenience.

No Battery

The internal battery is completely discharged or not 
installed.

If you turn off the power to the unit, the current settings 
will be lost and reset to the default values. Stop operating 
the unit, and contact a Yamaha dealer for battery 
replacement.

Param Access Err

The current setting cannot be displayed because the 
parameter you attempted to operate does not exist. It is 
possible that the component is not operating normally.

Save the current settings using DME Designer, execute 
the initialization (Delete All Data). If the problem persists, 
contact a Yamaha dealer.

Param Set Err

The current setting cannot be changed because the 
parameter you attempted to operate does not exist. It is 
possible that the component is not operating normally.

Save the current settings using DME Designer, execute 
the initialization (Delete All Data). If the problem persists, 
contact a Yamaha dealer.

Resume Data Lost!
Recall a Scene!

Current setting has been lost.

Recall the scene again.
If the problem persists, contact a Yamaha dealer.

Saving Failed

A save operation has failed.

Stop using the device immediately and contact a 
Yamaha dealer.

Slots Overloaded

The current being used by all cards installed in I/O slots 
exceeds the rated limit.

Make sure that the total current consumption of the cards 
used does not exceed the limit.

Store Disable

The scene store parameter is set to “Disable.”

Set the scene store parameter to “Enable” via the Utility 
display “Lock” page.

Storing Failed

Either the flash memory for storing data is full, or the file 
system has been damaged.

Reduce the number of unused scenes. Alternatively, 
delete the files saved via the File Storage function. If 
deleting these items does not solve the problem, execute 
the Delete All Data initialization. If the problem persists, 
contact a Yamaha dealer.

Used by ExDevice

The connector selected by the Internal HA Ctrl 
parameter or the MIDI Port parameter is already being 
controlled by an external device (such as the PM5D).

Stop control from the external device. If it is being 
controlled from the PM5D, turn off the CONNECT button 
in the PM5D's DME CONTROL screen.

Used by HA Ctrl

The connector selected by the MIDI Port parameter is 
already selected for internal head amp control from an 
external device.

Set the Internal HA Ctrl parameter to something other 
than the connector you want to select for the MIDI Port 
parameter.

Used by MIDI

This cannot be set, since the connector selected by the 
Internal HA Ctrl parameter is already used by the MIDI 
function.

Set the MIDI Port parameter to something other than the 
connector you selected for Internal HA Ctrl.

Status messages

Cable Disconnect

No network cable connected.

Make sure that a network cable is properly connected, 
and that all network devices are functioning normally.

Cannot be assigned

No parameter assigned.

—

Cannot Store

The scene data is protected.

Set the protect parameter to “OFF” via the DME Designer 
application. 

CAS. In Sync Err

The DME64N/24N clock is not in sync with the clock 
signal being received at the [CASCADE IN] connector.

Make sure that the DME64N/24N and the card or 
external source supplying the word clock are set to use 
the same word clock.

CAS. Out Sync Err

The DME64N/24N clock is not in sync with the clock 
signal being received at the [CASCADE OUT] connector.

Make sure that the DME64N/24N and the card or 
external source supplying the word clock are set to use 
the same word clock.

Connection to Master 
DME is Lost

Communication with the master DME device has been 
interrupted.

Check that all cables are properly connected, and than 
hubs, routers, and related devices are functioning 
properly.