DRX-2
DRX-2
108
The sound processing is always done in stereo (that
means separate left- and right-channel).
a) Record-Path:
The complete selection of the audio signal for recording is
done by a HEF4052 [7501], which is a dual four-to-one
multiplexer.
The input lines for the selector [7501] are coming either
from MSP [7600] (“AFEL”/”AFER”) or cinch rear in 1
(“AIN1L”/”AIN1R”) or cinch rear in 2 (“AIN2L”/”AIN2R”) or
the cinch in front (“AINFL”/AINFR”). The [7501] is
controlled via “RSA1”-and “RSA2”-signals coming from
the MSP [7600].TheMSP acts as a port expander of the
CC-P. The Op-Amp on the output [7504] is necessary for
performance reasons and acts also as a driver. The
selected signals “ARADC” and “ALADC” are directly fed to
the Audio-ADC.
As there can exist also a fifth input in case of DV-In is
present the corresponding analog audio signals from the
DVIO-board are firstly routed via extra cable and
connector [1960] to the MSP, which acts as a preselector
between audio from internal frontend or the DV-Input.
b) Line-Out-Path:
see chapter 4.3
c) Digital Audio Output-Path without IOE-Print:
Additionally to analog audio the set is also equipped with a
digital output via cinch plug [1951]. The signal is
generated on the dig. board and routed via audio interface
cable and connector [1900] to the Ana-PCB. Here the
“DAOUT”-line first passes a 6-fold inverter [7580] being
used as a driver and for performance reasons (noise
reduction, jitter, etc.). Afterwards a transformer [5580] is
necessary to achieve the correct level and also to have a
floating output with isolated ground before the signal is fed
via [3580] to cinch plug [1951]. The capacitors [2580],
[2582] and [2583] perform an AC-coupling between
connector- and set-ground.
d) Digital Audio Output-Path with IOE-Print:
see chapter 3.4.f
e) Digital Audio Input-Path with IOE-Print:
see chapter 3.4.g
4.3 Audio ADC/DAC
The conversion of analog audio signals from the record-
selector [7501] in the I/O (“ALADC”- & “ARADC”) is done
via UDA1361TS [7005]. This IC can process input signals
up to 2Vrms by using an external resistor [3039], [3041] in
series to the input pins. As the level from the DVIO-Board
is only 1Vrms a 6dB step can be performed by setting pin 7
of [7005] to 3,3V via [7006] and “PWONSW”-line
controlled by the CC-P to use the whole dynamic range of
the ADC. All required clock signals are generated on the
dig. board and only the audio data (“A_DAT”-line) are
routed from Ana- to Dig.-PCB for further processing.
The transformation of dig. audio back to the analog
domain is done by UDA1334BTS [7001]. All necessary
clock signals are coming from the dig. board and dig.
audio data (“D_DATA0”-line) are converted into analog
signals, which are available at pin 14 and pin 16 of [7001].
Afterwards an Op-Amp. [7002] (line driver & level
adaptation) which also works as a low-pass-filter to
increase signal performance (noise, distortions,...) is
passed. Then both signals (“ALDAC” & “ARDAC”) are
directly routed to the rear cinch output. The DAC has also
a mute possibility, which can be activated by setting pin 8
to 3,3V via [7003]. This mute is controlled either by the dig.
board (“D_IKLL”-line) or the “IPFAIL”-signal from power-
supply-unit.
In addition to that the DAC [7001] and the cinch outputs
can be killed (muted) in case of “digital silence” by the
circuit around [7008], [7009] and [7010], when no audio
data are available (e.g. “D_DATA0”-line zero).
The signals from the audio DAC part (“ARDAC”/”ALDAC”)
are directly routed to both cinch rear outputs, which are
connected in parallel. To avoid plops and any other
audible noise on the output there is a mute-stage
implemented [7509], [7511] for each channel. The
activation is done via “AKILL”-line, which is a combination
of the “KILL” from CC-P, “DAC_MUTE” from DAC-part and
“IPFAIL” from the power-supply-unit. The circuit around
[6430], [6431], [7430] and [7404] generates this signal.
Summary of Contents for DRX-2
