background image

Natural Sound Digital Sound Field Processor

4 Programs for Digital Sound Field Processing

2 Programs for Dolby Surround (DOLBY PRO LOGIC and ENHANCED)

60W (8

) RMS Output Power, 0.1% THD, 1 kHz (Center Channel Power Amplifier)

15W + 15W (8

) RMS Output Power, 0.7% THD, 1 kHz (Rear Channel Power Amplifier)

Automatic Input Balance Control for Dolby Surround

Test Tone Generator for Easier Speaker Balance Adjustment 

3 Center Channel Modes (NORMAL/WIDE/PHANTOM)

Remote Control Capability

Thank you for selecting this YAMAHA digital sound field processor.

CONTENTS

Safety Instructions  ................... 2
Supplied Accessories  .............. 3
Profile of This Unit .................... 4
Speaker Setup ...........................5
Connections ............................. 6
Identification of Controls  .......... 9
Speaker Balance Adjustment

............................................... 10

Using Digital Sound Field
Processor (DSP)  .................... 12
Notes about the Remote
Control Transmitter  ................. 15
Troubleshooting ...................... 16
Specifications ......................... 16

IMPORTANT!
Please record the serial number of this
unit in the space below.

Serial No.:

The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.

WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.

R I S K   O F   E L E C T R I C

S H O C K

CAUTION:  TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK), NO USER-SERVICEABLE

PARTS INSIDE, REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.

The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing)  instructions in the
literature accompanying the
appliance.

• Explanation of Graphical Symbols

CAUTION

OWNER’S MANUAL

DSP-E390

Summary of Contents for DSP-E390

















Reviews: