TRIGGER
Ref
erence
KIT
MIDI
V
OICE
UTILITY
W
A
VE
PA
TTERN
TRIGGER Setting Area (TRG)
Owner’s Manual
103
TRG2-2-2
Individual Crosstalk Level page
1
Pad
Use this parameter to select the pad(s) for which a crosstalk
level is to be set. You can also strike a pad to select it.
• Selection by striking is limited to pad groups (i.e., UP, MID, or LOW)
and the external pads (i.e., 13 to 17).
B
Crosstalk source
Use this parameter to specify a pad or group of pads causing
crosstalk in the pad(s) indicated by
1
. You can also strike a
pad to select it.
C
Crosstalk level
Use this parameter to specify a level for preventing crosstalk
from the pad(s) indicated by
2
. If the input level produced at
the pad indicated by
1
is lower than this level whenever the
pad indicated by
2
is struck, it will be treated as crosstalk
and no trigger signal will be generated. Although higher set-
ting values are more effective in preventing crosstalk, they
can also make it difficult to play multiple pads at the same
time.
Settings
UP, MID, LOW, or 01 to 17
Settings
UP, MID, LOW, or 01 to 17
Settings
0% to 99%
Typical Examples of Crosstalk-
Prevention Setup – No. 1
●
Use this approach when pad sensitivity is set
to allow playing by hand and striking of one of
the pads from the MID group (i.e., 4 to 9)
causes another pad from that group to pro-
duce a sound.
1
Navigate to the Individual Crosstalk Level page
(TRG2-2-2) and set its parameters as follows.
1
: MID (i.e., pads 4 to 9),
2
: MID (i.e., pads 4 to 9)
2
Hold down the [SHIFT] button and press the [UP/
DOWN] button to activate the input lock. (
will change to
.)
• The input lock must be activated here to prevent the selection
from changing when one of the other pads from the MID group
(i.e., 4 to 9) is struck in the next step.
TRG2-2-2≥-¡¢-≥˛¸
Level=≥25%(¡£)
1
3
2
NOTE
-MID-
[MID]
NOTE
3
While striking one of the pads from the MID
group (i.e., 4 to 9), raise the level indicated by
3
until other pads from that group no longer pro-
duce any sound.
4
Press the [STORE] button to open the Trigger
Store page, and then store your trigger setup as
described on page 45.
Typical Examples of Crosstalk-
Prevention Setup – No. 2
●
Use this approach when pad sensitivity is set
to allow playing by hand and, for example,
striking of Pad 4 also results in Pad 5 produc-
ing a sound
1
Navigate to the Individual Crosstalk Level page
(TRG2-2-2) and set its parameters as follows.
1
: 05 (i.e., Pad 5),
2
: 04 (i.e., Pad 4)
2
Hold down the [SHIFT] button and press the [UP/
DOWN] button to activate the input lock. (
will change to
.)
• The input lock must be activated here to prevent the selection
changing from Pad 5 to Pad 4 when Pad 4 is struck in the next
step.
3
While striking Pad 4, raise the level indicated by
3
until Pad 5 no longer causes a voice to play
(i.e., no longer produces a trigger signal).
• If this level is set too high, Pad 5 may not produce any sound
when struck relatively softly together with Pad 4.
4
Press the [STORE] button to open the Trigger
Store page, and then store your trigger setup as
described on page 45.
TRG2-2-2≥[MID]˛¸
Level=≥28%(MID)
1
2
3
-º∞-
[º∞]
NOTE
NOTE
TRG2-2-2≥[º∞]≥˛¸
Level=≥28%(04)
1
3
2
Summary of Contents for DTX-MULTI
Page 1: ...Owner s Manual EN ...
Page 114: ...114 Owner s Manual MEMO ...
