88
Owner’s Manual
UTILITY Setting Area (UTIL)
Pad Utilities
In the PAD section, you can assign functions to pads and external
controllers, specify the type of controller connected via the FOOT
SW jack, and enable or disable rim pads 10 to 12. With the PAD
page (UTIL4) displayed, press the [ENTER] button to access its
three parameter-setting pages (UTIL4-1 to UTIL4-3). You can use
the [
B
]/[
C
] buttons to navigate between these pages.
On the Pad Function page, you can specify operations to be per-
formed when individual pads or external controllers are struck or
operated.
1
Pad number
Use this parameter to select the pad or external controller to
be set. You can also strike a pad to select it.
B
Pad function (Func)
Use this parameter to set the operation to be performed when
the pad or external controller indicated by
1
is struck or
operated.
• off ....................... Voices will be played in the normal way.
• inc kitNo............. The kit number will be increased by 1.
• dec kitNo ............ The kit number will be decreased by 1.
• inc ptnNo ............ The pattern number will be increased by
1.
• dec ptnNo ........... The pattern number will be decreased by
1.
• inc tempo ............ The tempo will be increased by 1 bpm.
• dec tempo ........... The tempo will be decreased by 1 bpm.
• tap tempo ............ The pad or external controller can be used
to tap the tempo.
• clickOn/Off......... The click track will be turned on or off.
• CC01 to CC95 .... A MIDI Control Change message will be
sent to the internal tone generator and
connected external MIDI devices.
When a MIDI Control Change message (CC01 to CC95) is
specified as the pad function, control-change values and the
MIDI send channel are set as follows.
C
Control change value
Use this parameter to set a value for the MIDI control-change
message indicated by
2
.
•
If setting a pad or external controller other than
“FTSW”:
This value will be sent when the pad or external
controller is struck or operated.
•
If setting “FTSW” and “ftSw” is selected on the Foot
Switch Input page (UTIL4-2):
3
-a is the value that will
be sent when the foot switch is released, and
3
-b is the
value that will be sent when the foot switch is depressed.
•
If setting “FTSW” and “ftSw” is not selected on the
Foot Switch Input page (UTIL4-2):
A specific control-
change value cannot be specified in this case. Instead, a
value within the range 0 to 127 will be sent based on the
degree by which the hi-hat controller or foot controller is
operated.
D
Control-change send channel
Use this parameter to set a MIDI channel for sending the
MIDI Control Change message indicated by
2
.
UTIL4 PAD
UTIL4-1
Pad Function page
Settings
01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW
(foot switch), HHCL (hi-hat close), or HHSP
(hi-hat splash)
Settings
off, inc kitNo, dec kitNo, inc ptnNo, dec
ptnNo, inc tempo, dec tempo, tap tempo,
clickOn/Off, or CC01 to CC95
UTIL4
≥≥≥≥≥≥PAD
UTIL4-1≥-º¡-
Func=clickOn/Off
2
1
Settings
0 to 127
Settings
1 to 16
UTIL4-1≥-º¡-≥≥†”
Func=CC01/127
4
2
3
UTIL4-1≥-√¤‘’-†”
Func=CC01/≥0-127
4
2
3
-a
3
-b
UTIL4-1≥-√¤‘’-†”
Func=CC01
4
2
If setting a pad or external controller other than “FTSW”:
If setting “FTSW” and “ftSw” is selected on the
Foot Switch Input page (UTIL4-2):
If setting “FTSW” and “ftSw” is not selected on the
Foot Switch Input page (UTIL4-2):
Summary of Contents for DTX-MULTI
Page 1: ...Owner s Manual EN ...
Page 114: ...114 Owner s Manual MEMO ...
