Yamaha DTX700 Reference Manual Download

Page: 30 / 69

KIT

DTX700 Reference Manual

Settings:

off, snares, tuning, tempo, filter, snaresOn/Off

NOTE

•

The initial default setting of the PadCtrlType (Pad Control Type)
parameter depends on the drum kit selected.

•

The settings available for the PadCtrlType (Pad Control Type)
parameter depend on the trigger input jack that the pad has
been plugged into. For example, the settings “snares” and
“snaresOn/Off” are available only when the [

SNARE] trigger

input jack is being used.

Hi-hat Function (HH Func)

Use this parameter to specify how a hi-hat controller connected to
the [HI-HAT CONTROL] trigger-input jack is to function.

Settings:

hi-hat, MIDI

NOTE

•

When this parameter is set to “hi-hat” and “on” has been
selected for the SendHH (Send Hi-hat Controller) parameter
from the Menu area’s Utility/MIDI page, Control Change 4
messages corresponding to the degree to which the hi-hat
controller is depressed will be sent to external MIDI devices on
MIDI channel 10.

•

When this parameter is set to “MIDI”, MIDI messages are sent
regardless of the setting of the SendHH (Send Hi-hat Control-
ler) parameter from the Menu area’s Utility/MIDI page.

Hi-hat MIDI Channel (HH MIDI Ch)

If “MIDI” has been set for the HH Func (Hi-hat Function) param-
eter (also from the Menu area’s Kit/Pad page), use this parameter
to set the MIDI channel for output of the MIDI messages gener-
ated by the hi-hat controller.

Settings:

1 to 16

NOTE

•

If “hi-hat” has been set for the HH Func (Hi-hat Function)
parameter (also from the Menu area’s Kit/Pad page), this set-
ting will be displayed as “--” and modification will not be possi-
ble.

Hi-hat MIDI Type (HH MIDI Type)

If “MIDI” has been set for the HH Func (Hi-hat Function) param-
eter (also from the Menu area’s Kit/Pad page), use this parameter
to set the type of MIDI messages generated by the hi-hat control-
ler.

Settings:

CC01 to CC95 (Control Change), AT (Aftertouch), PBup
(Pitch Bend up), PBdwn (Pitch Bend down)

NOTE

•

If “hi-hat” has been set for the HH Func (Hi-hat Function)
parameter (also from the Menu area’s Kit/Pad page), this set-
ting will be displayed as “-----” and modification will not be pos-
sible.

Snare Wire On/Off (SnaresOn/Off)

Use this parameter to control the behavior of the pad connected to
the [

SNARE] trigger input jack. If set to “on”, the voices

assigned to the SnareHd, SnareOp, and SnareCl pads will be out-
put. If set to “off”, meanwhile, the voices assigned to the SnrHd-
Off, SnrOpOff, and SnrClOff pads will be output. For more
details, refer to

page 3

Settings:

off, on

Snare Wire Adjustment (SnaresAdjust)

Use this parameter to adjust the tightness of the snare wire.
Higher values correspond to tighter snare wires and vice-versa.

Settings:

1 to 15

NOTE

•

When you adjust this parameter, the Decay parameter* from
the Menu area’s Kit/Voice page also changes. (*: Applies only
when the VoiceCategory parameter has been set to “SnareHd”
or “SnareOp”.)

SnareBuzz

Use this parameter to specify how the snare wire effect resonates
with kick and tom sounds. The higher the setting, the greater the
degree of resonance. Set to “off” to prevent the snare wire from
resonating.

Settings:

off, 1 to 5

KIT/PAD 2/3

hi-hat

The hi-hat controller will function in the standard
way for playing the hi-hat cymbal.

MIDI

When you step on the hi-hat controller, a MIDI
message is output in line with the settings of the
HH MIDI Ch (Hi-hat MIDI Channel) and HH MIDI
Type (Hi-hat MIDI Type) parameters below.

KIT/PAD 3/3