This manual describes the standard assembly of the DTX900K.
After assembling the parts and connecting the cords as shown below, the Drum Trigger Module is ready to be turned on.
•
To assemble the unit, make sure you have the following four pack-
ages: RS130 (Rack System), DTP900 (Pad Set), DTP901(Pad
Set), DTX900 (Drum Trigger Module).
•
This manual covers how to attach the Pads and Drum Trigger Mod-
ule to the Rack System RS130, for which assembly has already
been completed. Before performing the instructions described in
this manual, make sure to complete the Rack System RS130 by
following the corresponding Assembly Manual.
Before assembling the unit, lay a drum mat (sold separately) on the
floor. Alternately, to prevent damaging the floor, lay the cardboard of
the included packages, etc. on the floor before handling the Hi-Hat
Stand HS740A and Kick Pad KP125W.
Before using, please read this assembly manual, and use this product in a safe and proper manner.
* Please keep this manual in a safe place for future reference.
* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.
NOTICE
• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,
never place any heavy or sharp objects on the cable. Applying excessive force to the cable may
result in damage to the cable, such as the wires being severed, etc.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,
close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).
Doing so may result in deformation, discoloration, damage or deterioration.
• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration
or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If
the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that
has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as
not to let the water and detergent come into contact with the cushions used in the product; doing so
may result in deterioration.
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifica-
tions, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
DTX900K
Assembly Manual
EN
PCY155
(Cymbal Pad)
PCY135
(Cymbal Pad)
PCY135
(Cymbal Pad)
XP100T
(Tom Pad)
XP100T
(Tom Pad)
KP125W
(Kick Pad)
CH755
(Cymbal Holder)
CH750
(Cymbal Holder)
RS130
(Rack System)
CH750
(Cymbal Holder)
Drum Trigger
module DTX900
RHH135
(Real Hi-Hat Pad)
HS740A
(Hi-Hat Stand)
SS662
(Snare Stand)
XP120SD
(Snare Pad)
Unit Standard Assembly
IMPORTANT
NOTICE
PRECAUTIONS
If this symbol is ignored and the equipment is used improperly, fatal
injury to persons or serious damage could occur.
• Do not let small children assemble or set up this product by themselves, or they may be injured.
Always assemble this product with adult supervision.
• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends
may result in injury.
• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends
may result in injury.
• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened
firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts
may result in the rack overturning or parts dropping, causing injury.
• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on
steps may result in the product being unstable and subject to overturning.
• When setting up the product, please pay close attention to the handling and setting of cables.
Carelessly placed cables may cause the user and others to trip and fall.
• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.
• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.
WARNING
If this symbol is ignored and the equipment is used improperly,
there is a danger or injury to persons handling the equipment, and
material damage could occur.
• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.
• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your
fingers.
• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting
in injury.
• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums
may drop, causing injury.
CAUTION
Assembling the Rack System
For details, refer to the Assembly Manual of the RS130.
Checking the contents of each package
Mounting the Pads and the Drum Trigger Module on the Rack System
Mount the Pads and the Trigger Module on the Rack System. Then position the Kick Pad and the Hi-Hat.
1
2
Package 1 [DTP900]
❑
PCY135
(Cymbal Pad) (2)
❑
PCY155
(Cymbal Pad) (1)
❑
RHH135
(Real Hi-Hat Pad) (1)
❑
KP125W
(Kick Pad) (1)
❑
CH750
(Cymbal Holder) (2)
❑
SS662
(Snare Stand) (1)
❑
Stand base for the
RHH135 (1)
❑
Hi-Hat clutch for the
RHH135 (1)
❑
Cable band for the
RHH135 (1)
❑
Stoppers for the
PCY135/155 (3)
❑
Felts for the
PCY135/155 (3)
❑
2.5m stereo phone
cables (7)
❑
4m stereo phone
cables (4)
❑
Cable bands (10)
❑
2m spiral tube (1)
* You can cut this tube to any desired length and
use it in order to take up any slack of the cables.
❑
Owner’s Manuals
(for each Pad)
• PCY65/65S/135/155
• KP125W
• RHH135
❑
Tuning key (1)
Package 3 [Drum Trigger Module DTX900]
❑
Drum Trigger Module
DTX900 (1)
❑
Module stand fastening
screws (4)
❑
Module Stand (1)
❑
AC Power
Adaptor (1)
❑
DTX900 Owner’s Manual (1)
❑
DTX900 Data List (1)
Package 2 [DTP901]
❑
XP100T (Tom Pad) (3)
❑
Clamp bolt (3)
❑
CH755
(Cymbal Holder) (1)
❑
HS740A
(Hi-Hat Stand) (1)
❑
XP120SD (Snare Pad) (1)
❑
Additional holder clamp (1)
❑
XP100T/100SD/120T/120SD
Owner’s Manual (1)
❑
Assembly Manual (this sheet, 1)
3
1.
Remove the right end support (shown below with
a
) of
the Rack, attach the additional Holder Clamp in the
direction shown below, then attach the support to the
Rack again.
2.
Attach the Cymbal Holders (CH750 x 2 and CH755 x 1)
to the Rack System as shown below.
Attaching additional Holder
Clamps and Cymbal Holders
CH750
CH750
CH755
Additional
Holder Clamp
a
Loosen the
screws.
1.
Attach the clamp bolt then tighten it with five or
six turns on each of three Tom Pads.
2.
Attach three Tom Pads to the clamp rods on the
rack respectively. As shown below, attach the
Tom Pad to the rod part so that the rod part is to
be inserted to the hole of the Tom Pad, then
tighten the clamp bolt firmly.
3.
If you want to change the location (height and
angle) of the Tom Pad, use the clamp bolts A
and B. Loosen the one of the clamp bolts,
adjust the location of the Pad, then make sure
to tighten the clamp bolts again before adjust-
ing another clamp bolt.
Attaching the Tom Pad
XP100T
Clamp bolt (to be
tightened as shown)
Tom pad (back side)
Clamp rod
Clamp bolt
To be
inserted
Rod parts
Tom pad
Clamp bolt A
Clamp bolt B
Continued on the next page (on the back side)
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
©2009 Yamaha Corporation
WT59070 910PO***.*01A0
Printed in Japan
dtx900k̲B3̲en̲1009.fm Page 1 Friday, October 9, 2009 4:42 PM
