Yamaha DTX900M Owner'S Manual Download

Page: 77 / 164

Basic Structure of the DTX900

Reference

DTX900 Owner’s Manual

um Kit mode

Ref

erence

Song mode

Clic

k mode

igger mode

File mode

Utility mode

Chain mode

Sampling mode

*1 The Bottom parameter is available only when the value is less than

that of the Top parameter.

*2 The Color parameter may not be effective depending on the values

of the Mode and Stage parameters.

*3 The Top parameter is available only when the value is more than that

of the Bottom parameter.

NoisModDpt

Determines the depth of the noise modulation.

NoisModSpd

Determines the speed of the noise modulation.

NoisTon

Determines the characteristics of the noise.

On/Off

Turns the isolator on or off.

OSCFrqCors

Determines the frequency for modulating the input
wave.

OSCFrqFine

Finely determines the frequency for modulating the
input wave.

OutGain

Determines the level gain.

OutLvl

Determines the output level.

OutLvl1

Determines the output level for the 1st series.

OutLvl2

Determines the output level for the 2nd series.

Output

Determines the output level.

OverDr

Determines the degree and character of the distor-
tion effect.

Pan1

Determines the pan position for the 1st series.

Pan2

Determines the pan position for the 2nd series.

PanAEGLvl

This parameter of the Slice effect determines the
minimum level of the AEG applied to the panned
sound.

PanAEGType

This parameter of the Slice effect determines the
type of the AEG applied to the panned sound

PanDirectn

Determines the type of the Auto Pan.

PanDpth

Determines the depth of the pan effect.

PanType

Determines the pan type.

PhShiftOfst

Determines the offset value of the phase modulation.

Pitch1

Determines the pitch in semitones for the 1st series.

Pitch2

Determines the pitch in semitones for the 2nd series.

PMDepth

Determines the depth of the pitch modulation.

Pre-LPF

Determines the Cutoff frequency of the Low Pass Fil-
ter before the modulation.

PreLPFReso

Determines the Resonance of the Low Pass Filter for
the input sound.

PreModHPF

Determines the Cutoff frequency of the High Pass
Filter before the modulation.

Presenc

This guitar amp effect parameter controls the high
frequencies.

Ratio

Determines the ratio of the compressor.

RelCurv

Determines the release curve of the envelope fol-
lower.

Release

Determines the amount of time that elapses between
the release or end of a sound and the end of the
compressor effect.

RelTime

Determines the release time of the envelope follower.

Reso

Determines the resonance of the filter.

ResoOfst

Determines the resonance as offset.

RevDly

Determines the delay time from the early reflections
until the reverberations.

RevTime

Determines the reverb time.

RoomSize

Determines the room capacity.

Rotor/Horn

Determines the volume balance of the horn and
rotor.

RotorF

Determines the speed of the rotor when the slow/fast
switch is set to “fast.”

RotorS

Determines the speed of the rotor when the slow/fast
switch is set to “slow.”

Sens

[For FLANGER&PHASER effects, TECH effects]
Determines the sensitivity of the modulation applied
to the input change.
[For TOUCH WAH]
Determines the sensitivity of the wah filter’s change
applied to the input change.

S-FTmHorn

Determines how long it takes for the rotation speed of
the horn to change from the current speed (slow or
fast) to another speed (fast or slow) when the rotation
speed is switched.

Paramater

name

Descriptions

S-FTmRotor

Determines how long it takes for the rotation speed of
the rotor to change from the current speed (slow or
fast) to the another speed (fast or slow) when the
rotation speed is switched.

SmplFrqCtr

Controls the sampling frequency.

SpcType

Selects the type of space simulation.

Speaker

Selects the type of speaker simulation.

Speed

[For FLANGER]
Determines the frequency of the LFO wave which
controls the cyclic change of the delay modulation.
[For PHASER MONO, PHASER STEREO]
Determines the frequency of the LFO wave which
controls the cyclic change of the phase modulation.
[For AUTO WAH]
Determines the speed of the LFO.

SpeedCtrl

Switches the rotary speed.

Spread

Determines the spread of the sound.

Stage

Determines the step number of the phase shifter.

Thresh

Determines the minimum input level at which the
effect is applied.

Top

Determines the maximum value of the wah filter.

Type

[For FLANGER]
Determines the type of flanger.
[For WAH effects]
Determines the type of Wah.
[For EARLY REFLECTION]
Determines the type of the reflection sound.

Vowel

Selects a vowel type.

WallVary

Determines the wall status of the simulated room.
Higher settings produces more diffuse reflections.

Width

Determines the width of the simulated room.

WordLen

Determines the resolution of the sound, or how
“rough” the sound is.

Paramater

name

Descriptions