25
TRIG2
¡snare
0%
–Type=
TP1/SnrA‚
Previous page icon
Trigger Input you want to edit
Next page icon
Flashing cursor
(the item you want to edit)
Completed!
3.
Rotate the jog dial to change the setting.
* An asterisk “
*
” will appear next to “
TRIG
” in the display if
data is changed. This asterisk will disappear after the store
operation is carried out.
* The Trigger Input Level produced when the pads are hit is
given on the upper right side in the display. When setting the
gain, use this level as a guide to measure how hard the
pads are being hit.
4.
To save changes you’ve made to the data, use the proce-
dure described below to store the data in User Trigger Setup
(No. 5).
* If a different trigger setup is selected before carrying out the
store operation, all changes you have made to the data will
be lost.
4-1. Press the [SAVE/ENT] button. The following display will
appear.
4-2. Press the [SAVE/ENT] button again and the following
display asking your confirmation to proceed with the store
operation.
4-3. Press the [SAVE/ENT] button to carry out the store op-
eration.
* To cancel the store operation, press any button except
for the [SAVE/ENT] and [SHIFT] buttons (when “Are you
sure?” appears in the display, the jog dial will also can-
cel the operation).
The following display appears after the store operation is
complete.
TRIG1 Trigger Setup Select
[Range] 1 to 5
Selects the Trigger Setup Type. (P. 24)
TRIG2 Type (Pad Type)
Sets the type of pad that is connected to the assigned input jack
shown in the upper half of the display ([1 SNARE] in the example
shown above).
* Values set in [TRIG3 Gain, MVl (Mininimum Velocity)] (P. 26)
and [TRIG5 SelfRejTime (Self Rejection Time)] (P. 26) will auto-
matically select the proper value for the pad type you set here.
Pad types are defined as follows.
KP
KP80S/80/65/60
TP1/SnrA
TP65S/65 (mainly used as a snare pad)
*1
TP1/SnrB
TP65S/65 (mainly used as a snare pad)
*1, *2
TP1/Tom
TP65S/65 (mainly used as a tom pad)
*1
TP2-A
TP80S/80/65/60
*3
TP2-B
TP80S/80/65/60
*3
PCY1
PCY150S
PCY2
PCY130S/130
PCY3
PCY80S/80/65/60/10
RHH
RHH130
RHP
Pad
RHP120SD/120/100/80 (pad side)
*4
RHP
Rim
RHP120SD/120/100/80 (rim side)
*4
RHP
Kick
KP120
BP
BP80
*5
DT
Snare
DT series drum trigger (for a snare drum)
DT
HiTom
DT series drum trigger (for small toms)
DT
LoTom
DT series drum trigger (for large toms)
DT
Kick
DT series drum trigger (for bass drum)
misc
1
to
6
Another manufacturer’s pad 1 to 6.
*1 3-zone function (pad voice x1, rim voice x2) is available to a 3-
zone compatible pad such as the TP65S, etc., if it is connected
to the 1 SNARE input.
When connected to the 5 RIDE or 6 CRASH jacks, the rim will
produce only one voice. For produc-
ing closed rim shots, the [
TP1/
SnrA
] has a high sensitivity setting
on rim 1, while the [
TP1/SnrB
] has
a high sensitivity setting on rim 2.
Left and right rim sensitivity is set
at the same level for [
TP1/Tom
]. If
the pad is connected to any other
input, the rim voice will not be pro-
duced and the pad will only produce
one voice.
Rim 2
TRIG1
1
:Medium
‚
TRIG2
¡snare
0%
–Type=
TP1/SnrA‚
Trigger Setup Edit
TRIG2*¡snare
0%
–Type=
TP1/SnrB‚
Trigger Input Level
TRIG
save
to
5
TRIG
save
to
5
Are
you
sure
?
Store
Destination
Rim 1
