1 Connections
14
DTXPRESS
IV
Owner’s Manual
5 Selecting the Trigger Setup
This setting lets you select the Trigger Setup that most closely
matches the trigger output levels and functions of your pads.
Select an appropriate Trigger Setup for your drum kit from the
pre-programmed Trigger Setups in the DTXPRESS IV.
Use the operation described below to select the Trigger Setup you
want to use.
●
Procedure
5-1.
Press the [SHIFT] + [DRUM KIT] buttons to view Page 1 in
the Trigger Setup Select display (TRG1).
5-2.
Rotate the jog dial to select the Trigger Setup that matches
the drum kit you are using.
●
Trigger Setup List
TRG1
~~~
ååååååååå
1
~
:SP
~
Med
~~~~~~
‚
Trigger Setup
TRG1
~~~
ååååååååå
4
~
:STD
~
Med
~~~~~
‚
• If you want to replace some of the pads from the DTXPRESS IV
Standard Set / Special Set, refer to the operation on page 36 (Trig-
ger Setup Edit) after the above setting is done, to make sure that
the settings (such as sensitivity) are appropriate for each pad.
NOTE
●
About Connecting Pads
• The DTXPRESS IV’s input jack parameters are preset with
settings suitable for pads when an appropriate Trigger Setup
is selected. If you intend to connect any other type of pad or
a drum trigger (Yamaha DT20, etc.) to the input jack, that
jack’s parameters (sensitivity, etc.) should be changed to set-
tings that suit the particular pad. Pad sensitivity is set in the
Trigger Setup Select display’s Page 3 [TRG3 Gain] setting
(p. 38).
• Pad-controller-equipped pads like the TP120SD, TP100,
etc., can be connected to Trigger Input jack
1
SNARE.
• Three-zone pads like the TP65S, PCY150S, PCY130SC,
etc., can be connected to Trigger Input jacks
5
RIDE and
6
CRASH.
•
7
HI HAT is a stereo input type jack. Pads equipped with
trigger switches like the TP65S, PCY65S, PCY130S, etc.
can be connected to this jack.
• The
2
TOM1/10,
3
TOM2/11,
4
TOM3/12 jacks corre-
spond to a two-trigger input that uses a stereo jack for L and
R. A parallel cable (stereo plug—mono jack x 2) can be
used to input two trigger signals.
• The
8
KICK/9 jack accepts a two-trigger input using a ste-
reo cable and jack for L and R signals. A parallel cable (ste-
reo plug—mono jack x 2) can be used to input two trigger
signals.
Also, if the KP65 kick pad is connected to the DTXPRESS
IV’s input jack 9 with a stereo cable, the external pad input
jack on the KP65 can be used as the input for Input jack 9.
• In addition to the
8
KICK/9 jack, the
2
TOM1/10,
3
TOM2/11, and
4
TOM3/12 jacks can be used to connect
a second bass drum pedal to create a double-bass drum set.
* In the default setting, "1. SP Med" for Special Drum Set is selected.
No.
Name
Features
1
SP Med
for Special Drum Set
Normal setting
2
SP Dyna
Wide dynamic range. This setting is designed for maximum expressive control, allow-
ing performance subtleties over a wide dynamic range. Excessive vibration however,
may result in crosstalk (sound being produced by other pads).
3
SP Easy
Controlled dynamic range delivers stable trigger detection. This setting is designed
for producing a smoother, more uniform sound with reduced volume fluctuations.
4
STD Med
for Standard Drum Set
Normal setting
5
STD Dyna
Wide dynamic range. This setting is designed for maximum expressive control, allow-
ing performance subtleties over a wide dynamic range. Excessive vibration however,
may result in crosstalk (sound being produced by other pads).
6
STD Easy
Controlled dynamic range delivers stable trigger detection. This setting is designed
for producing a smoother, more uniform sound with reduced volume fluctuations.
7
DT10/20
—
Use for DT10/20 drum trigger systems applied to acoustic drums.
8
|
11
UserTrig
—
Allows creation of custom trigger setups. (
→
→
→
→
Settings are made using Trigger Setup
