37
1-3. Velocity Curve
This function sets the MIDI Velocity Curve for the sensitivity for
each input jack
q
.
1-5. Specific Rejection
This function prevents cross talk from occurring between two speci-
fied input jacks
q
and
e
.
q
TRIG IN (Trigger Input Number)
Assigns the trigger input jack number (the same procedure as in
[1-1. Pad Type]).
w
VelCurve (Velocity Curve)
Sets the Input Velocity Curve for the trigger input jack assigned in
TRIG IN
q
.
1-4. Self Rejection, Rejection
This function is used to prevent double triggers
*
and cross talk
(mixed input signals between the jacks) for each input jack
q
.
*
double trigger:
When 2 sounds are played at the same time.
q
TRIG IN (Trigger Input Number)
Assigns the trigger input jack number (the same procedure as in
[1-1. Pad Type]).
w
SelfRej (Self Rejection)
[Range]
0-9
Prevents double triggers from occuring in the input jack assigned
in TRIG IN
q
. After an event is detected, further events will be
automatically muted for a certain length of time. Larger values set
longer times.
e
Rej (Rejection)
[Range]
0-9
Prevents cross talk from occuring in the input jack assigned in
TRIG IN
q
. Events triggered by other pads (input jacks) that are
of a lower input value than what is set here will not be delivered
for a set length of time.
q
TRIG IN (Trigger Input Number)
Assigns the trigger input jack number (the same procedure as in
[1-1. Pad Type]).
w
SPCRej (Specific Rejection)
[Range]
0-9
After an event occurs from the pad from the input jack assigned in
e
, the pad of the input jack assigned in TRIG IN
q
will not
sound for a certain length of time unless the level is greater than
the value assigned here.
e
frm (Assigned Destination Trigger Input Number)
[Range]
1-10, 6&7
Sets the destination trigger input jack number of the pad that will
be rejected. When “
6&7
” is selected, both trigger inputs 6 and 7
will be assigned.
1-6. Trigger Setup Copy
This function copies all data settings in [1-1. Pad Type] to [1-5.
Specific Rejection] from input jack
q
to another input jack
w
.
When the Trigger Setup Copy operation is carried
out, the trigger setup data will be replaced with the
settings of the copy source.
q
TRIG IN (Trigger Input Number)
Sets the trigger input jack number (1-10) of the pad copy source.
w
Copy to Input (Trigger Input Number Copy Destination)
Sets the trigger input jack number (1-10) of the copy destination.
Procedure
1.
In the display shown above, assign the copy source and
copy destination, press the [SAVE/ENT] button. The fol-
lowing display will appear asking for confirmation before
the copy operation is carried out.
TRIG
IN=
1
VelCurve=
normal
w
q
TRIG
IN=
1
SelfRej=2
Rej=
3
w
e
q
TRIG
IN=
1
SPCRej=0
frm=
1
q
e
TRIG
IN=
1
Copy
to
Input=
1
w
q
Trigger Setup Edit Mode
normal
hard
2
hard
1
loud1
loud
2
Input
Copy
to
1
Are
you
sure
?
2.
Press the [SAVE/ENT] or [VALUE+] button, the copy
operation will be carried out.
* Press the [VALUE-] button to cancel the copy operation.
When the copy operation is complete, “
Complete!
” will appear.
w
Strength
of hit
m
V
elocity
m
Summary of Contents for DTXPRESS
Page 1: ...DRUM TRIGGER MODULE Owner s Manual ...
Page 62: ...62 MEMO ...
